WANTED Any C Body part close enought to fit? B Body 1/4 window felt

Status
Not open for further replies.

odcics2

Well-Known Member
Joined
May 14, 2014
Messages
688
Reaction score
565
Location
utica, mi
Feedback: 1 / 0 / 0
Contact seller
I need a pass side 1/4 window felt for the outside of a 68 to 70 Dodge 2 dr. B Body hardtop.
Pics below are of my outside driver side part in usable condition. It shows the style I need to find. Notice there is no stainless bead running along the top! It's all black.

Are there any C Body weatherstrips where I could trim it down to make it work?? My driver side is 25.5" long. I can bend the end & attach it to the 1/4 panel however necessary.

I have no reproduction parts on the car, so that's why I'm looking for an used, original part.

PM please, if you have a part that can help!
WTB - rear outside catwhiskers - 68-70 coronet charger 001.JPG
WTB - rear outside catwhiskers - 68-70 coronet charger 002.JPG
WTB - rear outside catwhiskers - 68-70 coronet charger 003.JPG
WTB - rear outside catwhiskers - 68-70 coronet charger 004.JPG
 
I've got a 68 Fury 4 door I haven sold much from. I can check it. I'll be out there in the yard this weekend. Remind me Friday to look if you haven't found anything
 
ok, will do. Thanks!

Would a low line 69 to 73 Plymouth or Dodge C body 2 door piece work?
Thinking the pass door is long enough. Just wondering if it has a stainless bead, or not. (I need without)

Any idea?
 
Last edited:
Those Quarter window seals were pretty generic back in the day. For example my previous ’70 New Yorker 4d Hardtop had the same seal as many ’65-’72 A and B-bodies (Metro Seal VS 7-A/FL). In fact it was only listed for A and B-bodies.

I suggest you take a look at the Metro Seal website, and decide for yourself:

www.metrommp.com
 
Good idea. I can see what might interchange - meaning long enough to trim down.
That would expand my search for the real thing!
THANKS!
 
I did get out there to the car. We've had a lot of weather & between the ice, pine straw, dirt & being wet I can't tell how good they are. I think I have a long set from a mid 70's New Yorker. I can look at those tomorrow if you like. I remember they where pretty long
 
I did get out there to the car. We've had a lot of weather & between the ice, pine straw, dirt & being wet I can't tell how good they are. I think I have a long set from a mid 70's New Yorker. I can look at those tomorrow if you like. I remember they where pretty long

Don't put yourself out if the weather sucks!
Sure - when you can , check the New Yorker.
Need 26" long and no stainless bead running the length.
(guess I could have said all black!)
Much appreciated.
 
Would a low line 69 to 73 Plymouth or Dodge C body 2 door piece work?
I don't know. Mine on my '70 ragtop are gone. However, they dd not have clips as the ones you've pictured do. They "slid" into a slot on the window trim. The trim is attached to the window via glue; again, no clips.
 
IMG_3952.JPG
IMG_3955.JPG
IMG_3953.JPG
IMG_3954.JPG
Ok I have 2 more that might work. The red one is on a 64 Barracuda & the blue one is a wider soft felt from a 68 Monaco 4 door. If either or both will work let me know as it looks like I'll be in the yard all day Saturday pulling parts & I can get them then.
 
On the blue one, do you have the outside one?
Interior parts are "fuzzy", exterior are the 'felt sweeps'.
 
ok.
Outside ones are what I need.
The 3 you sent are great, one more like that! (or 2 !)
 
Status
Not open for further replies.
Back
Top