77newyorker440's Recent Activity

  1. 77newyorker440 replied to the thread Welcome Charlie71 to FCBO!.

    Welcome from the East Coast!

    Nov 29, 2020 at 7:52 AM
  2. 77newyorker440 replied to the thread Worst factory welds ever....

    You may not find a bad weld, but you will find oil all over your garage floor every time you park the car, at least from my experiences.

    Nov 29, 2020 at 7:51 AM
  3. 77newyorker440 replied to the thread Welcome Eric McIntyre to FCBO!.

    Welcome from the East Coast!

    Nov 28, 2020 at 10:16 PM
  4. 77newyorker440 posted a new thread.

    Electrical Keeps Getting Worse-77 New Yorker

    Hello Guys, Many things have happened with the Chrysler's electrical system since I last posted here, so I am going to lay them out...

    Forum: Electrical & Ignition

    Nov 28, 2020 at 10:11 PM
  5. 77newyorker440 replied to the thread Pls Help: Upper Ball Joint Too High?? 77 New Yorker.

    Good News! Decided to unwind the torsion bar on the driver's side, and we were easily able to put the ball joint in. Then, when...

    Nov 28, 2020 at 9:48 PM
  6. 77newyorker440 replied to the thread Welcome 60Buick to FCBO!.

    Welcome from the East Coast!

    Nov 27, 2020 at 5:58 PM
  7. 77newyorker440 replied to the thread Pls Help: Upper Ball Joint Too High?? 77 New Yorker.

    So far, I have changed the shocks, tie rods and sleeves, bumpers, and sway bar links. The upper ball joint was the next step, and I was...

    Nov 27, 2020 at 10:53 AM
  8. 77newyorker440 replied to the thread Pls Help: Upper Ball Joint Too High?? 77 New Yorker.

    Awesome, thanks for letting me know, when I do the passenger side one I will definitely fully tighten it down into the UCA so it is...

    Nov 26, 2020 at 8:21 AM
  9. 77newyorker440 replied to the thread Pls Help: Upper Ball Joint Too High?? 77 New Yorker.

    Yes, I actually own the manual, I honestly just forgot to pre-read, that's my bad, but it shouldn't happen again in the future, and I am...

    Nov 26, 2020 at 8:20 AM
  10. 77newyorker440 replied to the thread Pls Help: Upper Ball Joint Too High?? 77 New Yorker.

    Yep, I ordered the tool from O'Reilly's, it should come in tomorrow, so I'll tighten that ball joint down and see what happens. Thanks...

    Nov 26, 2020 at 8:17 AM
  11. 77newyorker440 replied to the thread Pls Help: Upper Ball Joint Too High?? 77 New Yorker.

    I don't think it is incorrect, according to Dave's description I think it is accurate. This is the one I got: Front Bump Stops - Dodge...

    Nov 26, 2020 at 8:16 AM
  12. 77newyorker440 replied to the thread For Sale 1972 Chrysler.

    It may just be an error on my end, but I think the Facebook ad may have been taken down.

    Nov 26, 2020 at 7:44 AM
  13. 77newyorker440 attached a file to the thread Pls Help: Upper Ball Joint Too High?? 77 New Yorker.

    Awesome, thank you, sir, it was just an honest mistake on my dad and I's part, we will definitely not press it in on the passenger side....

    20201125_164727.jpg Nov 25, 2020 at 4:05 PM
  14. 77newyorker440 replied to the thread Pls Help: Upper Ball Joint Too High?? 77 New Yorker.

    Okay, ill try that in a bit, I just have to figure out what to do with my upper ball joints due to my mistake, hopefully, I can just...

    Nov 25, 2020 at 3:42 PM
  15. 77newyorker440 replied to the thread Pls Help: Upper Ball Joint Too High?? 77 New Yorker.

    Dman, I didn't realize that, it didn't really appear to have threads, it really just seemed to have ridges, I'm used to just pressing...

    Nov 25, 2020 at 3:40 PM