Recent content by Patches66fury

  1. P

    1966 fury restoration

    I do like the the old style wheels. Problem is everyone has them so they have become me-too wheels. I hate going to car shows and seeing 4 styles of wheels. I'm 42 so these cars have been around my whole life. And after 42 years everyone is still running the same wheels, and all the cars look...
  2. P

    1966 fury restoration

    Well she is up and running and a few short test drives and a but of tire smoke. Next I need to get the holley sniper 2 and hyperspark installed so I can finish up the wiring.
  3. P

    1966 fury restoration

    Hood and fenders are back on. I have 3 hoods so I'm cutting this one up for the scoop. I was hoping to have it on the road last summer, but I had a few people nudge me into opening my shop before my car was done.
  4. P

    1966 fury restoration

    So it's been a bit and progress has been a bit slow but she is coming together. The dash is in and the console mock-up is done. I have started on building the console but I'm still not 100% sure on on a few things with it.
  5. P

    1966 fury restoration

    She is starting to look like a car again. It's also really nice to finally see the color on it. I have only seen it on a color card.
  6. P

    1966 fury restoration

    We little progress report. I got the trunk, doors and firewall all jambed. Got the engine back in, and the deck lid back on. And started on the dash. Now that the engine is back in I need to finish bashing my free b body header so they clear. I used the old torsion bars to get them close but...
  7. P

    1966 fury restoration

    So I have 2 parts cars si I have 3 dashes so I took one and did some cutting to fit my speedhut gauges. I got it mocked up so now it's fiberglass fun time to make my custom dash. I want it to still appear somewhat stock and not a completely new dash. I still haven't decided on a radio yet. I...
  8. P

    1966 fury restoration

    Well I finally hit a huge milestone in my build. The most time consuming part of scrapping, grinding and cleaning off old paint, seam sealer and surface rust is finally over. Now it's time to get her back together and on the road. I got the stub frame, floor, inside the roof, and underside...
  9. P

    1966 fury restoration

    Well the transmission tunnel is welded in.
  10. P

    1966 fury restoration

    OK so after waiting for what seemed like forever I finally have what I need to get her back on the road. I even have my paint so I can jamb it and start getting it on the road. The rear suspension is in, and the front is all torn down and ready to pull the engine So I can finish the...
  11. P

    1966 fury restoration

    I can see if I can get to it and take some measurements tomorrow. I will send you a message when I get them.
  12. P

    1966 fury restoration

    Dana 60 is in and ready for brakes. Unfortunately I'm waiting on parts to ship so I can get my rear stabilizer and shocks. Once I get that I can get the rear finished up and measure for the driveshaft. The entire front suspension is supposed to ship with it so them I get that done before spring.
  13. P

    1966 fury restoration

    Yes it's open headers and short collectors. I haven't got the headers I want yet and I didn't want to mess them up during cam brake in. And the cam is a Clay Smith. It's .480 lift 231 @ .050 and 108° I called them and that's what they suggested for my setup and what I'm going to use use car...
  14. P

    1966 fury restoration

    OK so I figured I out once but now it keeps saying it cannot embed the video. So here is the link to another one with a small rev https://youtube.com/shorts/_v0hIeJy888?feature=share
  15. P

    1966 fury restoration

    OK I think I figured out how to upload a video of the engine running
Back
Top