Search results

  1. R

    Gear Vendors Overdrive

    Looks like there are shorty, 8”, 15” and 18” adaptors for the torqueflite. Mine came with one that is 13.5” so I guess that is considered the 15”. I think the 18” would be the best fit as it would hang the overdrive behind the crossmember, up under the seat where there's more room in the tunnel...
  2. R

    Gear Vendors Overdrive

    Might be a different adaptor or crossmember but there's no way the stock crossmember was going to or on this one.
  3. R

    Gear Vendors Overdrive

    Not sure what the short adaptor looks like. Possible I guess.
  4. R

    Gear Vendors Overdrive

    Yeah, it certainly won’t fit right without some modification. I think cutting and rewelding is the most likely option.
  5. R

    Gear Vendors Overdrive

    Has anyone got any pictures of a Gear Vendors overdrive in a C body? How much did you modify the floor pan and crossmember? What sort of angle did the engine and trans end up at and did you lose any ground clearance? I've got a '68 Plymouth Suburban that is getting a 440/727/GV. I’ve had to...
  6. R

    Plug Wires and Distributor Collars

    Thanks for the replies. halifaxhops, I’ll send you a pm
  7. R

    Plug Wires and Distributor Collars

    I’m looking to get some new plug wires for my 440 and want a straight connector where they attach to the distributor as I think they fit much nicer than 90 degree ones. I also want cut to fit wires as the lengths on the assembled wires never seem to be right. Any suggestions for where I can get...
  8. R

    For Sale Nice Set of 4 1968 Plymouth Wheel Trims

    Great condition set of full wheel covers for 14” rims from 1968 Plymouth. No dents or scrapes. $50 obo plus shipping, or pick up from Fullerton, California.
  9. R

    Sun Visor Tips

    Perfect, thanks!
  10. R

    Sun Visor Tips

    The sun visors on my '68 Fury don’t clip into the mirror properly - it looks like there is probably a plastic or rubber tip that has fallen apart with age. Does anyone repop them?
  11. R

    What seats will fit '68 Fury?

    Thanks Ed, was good meeting you! The seat should be a nice upgrade.
  12. R

    1968 Plymouth Fury III Parts

    Do you have a nice dash pad? How about a working speedometer?
  13. R

    Can you remove and refit inner fenders without pulling the fenders?

    Sounds like that would be worth a try. I’ll give it a go when I get to that point.
  14. R

    Can you remove and refit inner fenders without pulling the fenders?

    I guess the stud is welded to the stub-frame? Would it help to drill the stud out and tap the frame for a bolt instead?
  15. R

    Can you remove and refit inner fenders without pulling the fenders?

    Unfortunately the '67-68 is a different design. As Furygt said, it looks like the radiator support would have to come out too and I’m not sure that can be done without disturbing the fenders. I’ll have a closer look when I pull the motor but I’m leaning towards leaving it all in place.
  16. R

    Updating AC

    Thanks, that makes sense. I’ll add it to the list!
  17. R

    Can you remove and refit inner fenders without pulling the fenders?

    Thanks for the replies. The front clip has never been off and all fits nicely so if I’d have to realign anything I’ll just leave the inner fenders and work around them.
  18. R

    Can you remove and refit inner fenders without pulling the fenders?

    Thanks, I don’t really want to pull the whole clip. It’s not a high end resto, I just want to clean it up a bit. I will be rebuilding the front suspension at the same time though.
Top