Search results for query: *

  • Users: MJFUR
  • Content: Threads
  • Order by date
  1. M

    69 Chrysler 300 Rear Housing Removal

    I have a 69 Chrysler 300 with A/C. Heat, DEF, A/C, MAX A/C all work correctly. The only problem is that when running the A/C some of the condensation/water leaks out of the rear housing and into the car. I usually just throw a towel under it to absorb the water. Both firewall drains are clear...
  2. M

    WANTED Torsion Bar Bolt/Swivel

    Looking for a set of Bolt/Swivels for a 69 Chrylser 300, part # 2525087. Chrysler & Dodge are the same, Plymouth is different. Thx, Mike
  3. M

    Torsion Bar Bolt/Swivel Adjustment

    69 Chrysler 300, re-installing the swivel bolt with car jacked up. Got about three quarters back in and blamo the bolt shoots back out. It stripped the threads from the bolt shaft. You can spin the threads like a washer on the shaft. Is 2525 087 still a good part # for the Chrysler/Dodge...
  4. M

    Original Headlights?

    69 Chrysler 300, headlights are dim, going to replace. If what I have are still original bulbs I'll save them. I can post pics if needed. Low Beams marked - General Electric, Sealed Beam, 2 High Beams marked - Wagner Halogen, 1C1 or ICI (I presume these are most likely replacements.) Thx
  5. M

    Fuel Tank Vent

    69 Chrysler 300 with new fuel tank, fuel lines, rubber hoses, vent tubes cleaned with brake cleaner, pipe cleaners and compressed air to verify positive air flow. The car has been up and running a little over a year now. Recently I've noticed that after filling the fuel tank I will get overflow...
  6. M

    Axle Leaking

    What is happening here? 69 Chrysler 300, the rear end has been rebuilt 4 times in the last 3000 miles. 8 3/4 Diff Dilemma I saw some leakage on the backside of the Rear Drivers Side tire, figured it was the brake cylinder. When I took it apart, it sure looks like a thick red grease or oil...
  7. M

    69 Chrysler Dyno data, Manifolds, Headers, Carbs

    Here’s some dyno data for a few parts and configurations. Yours will vary. 69 Chrysler 300 with 505ci, A727, 2000rpm Stall, 3.23 Sure Grip, 2.5” TTI Exhaust with Dyno Max Mufflers. 505ci Specs, Edelbrock Performer Intake Manifold, Lunati Voodoo, Duration (Int/Exh): 268/276; Duration @ .050...
  8. M

    For Sale Armrests B-Body, C-Body

    Set of repro Black Armrests, $30 - shipped USA.
  9. M

    WANTED 440 Oil Dipstick Tube

    Looking for the Oil Dipstick Tube for my 69 Chrysler 300, 440 (P/N 2899897). Mine just broke. I would imagine most C-body 440's are the same. Thx
  10. M

    Transmission Cooler Lines and TTI Headers

    Trying to find some "detailed" information on transmission cooler lines. I have a 69 Chrysler 300, Automatic, the car came with the base 440 (single exhaust). When I converted to HP manifolds and TTI 2.5" exhaust the transmission lines needed to be adjusted/bent a bit for the new driver side...
  11. M

    TTI Headers - Oil Dipstick Tube?

    After installing TTI Headers will the Dipstick tube re-attach to the engine mount or does it need modified? Thx
  12. M

    TTI Headers - Plug Wires?

    Installing TTI Headers, what type of plug wire set up did you use and configuration (straight or 90 degree boots), heat shields, etc.? I'm converting from HP Manifolds and the repro OEM wires which do not look like they will work. Photo's would be great. Thx
  13. M

    Torsion Bar Removel?

    69 Chrysler 300. Trying to remove my torsion bars to install TTI headers. Service Manual says to Remove Upper Control Arm Rebound Bumper. Unfortunately the stud in it just spins with nut. MUST it come out to allow more droop? If so, it will need cut out. I have the lower anchor adjusting bolt...
  14. M

    1970 Chrysler 300H - SOLD $40K MECUM

    Sold, Sold, Sold! 1970 Chrysler 300H | F80 | Glendale 2023 | Mecum Auctions
  15. M

    Carb/Throttle cable pin?

    69 Chrysler 300, auto. What is the proper name or part # for the pin/rod on the carb that the throttle cable/transmission rod attach too? Needs to be approx 1.75". Thx
  16. M

    69 Chrysler Window Seals

    69 Chrysler 300 Four Door Hardtop, is there a part number for the rear window forward seal or must you find a complete window? Is the part number for a left or right?
  17. M

    Spare Tire - Jack Assembly

    69 Chrysler 300 Four Door Hardtop, I pulled out the Spare Tire/Jack Assembly for the first time and found a little black clip laying under there. Is it part of the jack assembly? Where does it go?
  18. M

    8 3/4 Diff Dilemma

    69 Chrysler 300 with 8 3/4, 2.76 Open Axle, 489 Third Member that was converted to a 3.23 Sure Grip. Four rebuilds in 2800 miles. I'm not sure which way to go at this point. First rebuild Convert the 2.76 open axle to a 3.23 Sure Grip. All the typical conversion parts from Dr. Diff.. A...
  19. M

    CFM vs Cubic Inches

    Considering a carb upgrade. Current carb is a 4640S (750cfm) rebuilt by Woodruff carb. It runs and performs excellently, but I can't help think that it may be a little small for the cubic inches. I should probably leave well enough alone, but I'd hate to leave 20 or 30 HP on the table with an...
  20. M

    Trim Tag Screw

    My car has an incorrect Trim Tag Screw (right side). Anyone have a spare proper one they could part with? Thx Above the right hand screw is stamped "38". What does that indicate?
Back
Top