Search results for query: *

  • Users: 66furys
  • Content: Threads
  • Order by date
  1. 6

    Big block damper install

    Anyone remember the pressing on of a big block harmonic damper?? I am building an install tool and want to use 3/8 rod to pull. But, if they are very tight, I will have to up the size. Prob heat the damper a taste to help and will use a bit of never seize....but am curious how tough you have...
  2. 6

    Steering wheel repair

    So mine was medium bad, with some quarter inch gaps, and cracks. So, eastwood repair kit. The epoxy is great for the big gaps and is very slow to dry, so is not friendly for multiple apps. So, after getting the main repairs done, I switched to bondo for MANY repetitions of fills and sanding...
  3. 6

    Timing chain replace, et al

    Have only done a bit of homework on this so far, and am just punting to get started. 66 fury 383. But, with some rear main seal leaks, the work begins. So, several questions for those who come before me on issues. I will just go down the list.....first, there is one oil pan bolt that is...
  4. 6

    Lower windshield trim fasteners

    Have not had any success after trying some ebay fasteners that appeared to be in the neighborhood, but not. Some time back, this photo was put on this forum, and is the set I need. This is the first I have found on the outer clips that have a screw, and my spring clips are either in bad shape...
  5. 6

    Resto work on bucket seats

    I am not trying to restore....I took five years on an MGA frame off. My 66 fury is RoadKill, and I want to drive it. But, as an example of just how much is involved in a resto, my bucket seat is one. I pulled the seats for floor pan work and carpets. Sent just one seat base off for cushion...
  6. 6

    Aluminum trim polishing

    Having tried to research a means of polishing the anodized aluminum, I have not found much other than sand off, polish and re-coat. Anyone have any luck with this horrible trim. I am not sure yet whether it can be improved at all with a cleaner that does not remove the anodize??
  7. 6

    Console cover fasteners

    I hate to always ask the dumb questions......My car has been disassembled quite a bit over the life of the 66 sport fury. I keep hoping to find something original....maybe the engine?? Does anyone know what type nutz were used on the die cast console lid studs. Mine had a couple of different...
  8. 6

    Variable wiper with park

    For only a couple years, mother mopar used this park device, at least I think this is it, from service manual. Mine is MIA. IF correct, they are expensive and my motor fries the fuses, so has issues and will need rebuild. My question is this. Has anyone tried to replace this 66-68 system...
  9. 6

    Interior paint colors

    I have done just a few searches on this, found the 70 hamtramck pages, but need to find what paint code may have been used on my red interior 66 fury. Have not found a build sheet. Anyone have suggestion on red paint code used on things like the console in 66?? thanks
  10. 6

    My carpet fun

    Got the carpet with mass backing, makes it quite heavy and not very pliable. I am thinking that next time not the heavy stuff. And, and, and, I want to try next time to get separate padding. I tried to remove the padding anywhere I had to drill, cut or need to be thin....but I missed some...
  11. 6

    Wiper motor crank arm

    This 66 fury has a three speed wiper motor with a missing crank arm....interesting. But, as there are few out there and they are expensive, I wanted to ask about the correct one before trying to purchase. Does anyone have some info on the design of the arm, like the offset bend amount and the...
  12. 6

    Rear seat back on sport fury

    There is a large trim piece on top of the seat back that appears to be attached to the deck panel. Anyone pull this apart and have some thoughts for me. If the seat has to lift off of brackets, it means this trim has to go first. When I was young, I would just charge ahead, often at my...
  13. 6

    Cowl fresh air venting

    I have been chastised for silly questions, but have another. I am fighting the water intrusion from the cowl that rusted my driver side floor, and will now pull the kick panels to install carpet. I have not yet pulled the cowl, and am wondering how the huge amount of leaves get into the vent...
  14. 6

    Floor pan replace

    I have been working on mine now for quite a while.....most videos seem to say that this is done in a day or two.....hmmm. I bought this car because there was not much rust, and esp in the frame members, including the subframes. The main problem on this one was in the driver pan. I ordered...
  15. 6

    Notes on the cowl drains

    Note sure if this has been available here, but just wanted to add if not....have not found it on searches yet. The one confusing thing for me to date, is that I cant find how there are layers on the firewall to funnel water from the cowl areas up top, down even to the center flap hole, nor all...
  16. 6

    Holes in the floors, or in my head

    I usta have to travel to the tank plant in detroit, or just north....tried to get the hard heads to come up with a new main battle tank that weighed in at less than 80 tons, and get lean like the russians. But, they just kept the path. And now, I am dealing with the myriad round holes in the...
  17. 6

    nWater intrusion

    So, I have just pulled the major parts of my carpet.....in fact, two layers, and the driver side sheet metal is crap. Pass side seems pretty good so far. Have not pulled the windshield cowl, but am wondering about where the water came from on the driver side. The metal is real bad from up in...
  18. 6

    Rear seat remove again

    I pulled an old one back in the day, and recall push back and it will pop up. So, I finally have one bucket out and working carpet and rust. Tried to push on the back seat....nada mas. After pulling both carpet and pad from under the front of the seat you can easily see the bracket and the...
  19. 6

    Center Console Removal

    Yes, another dumb question for the seasoned audience. I am starting the removal of the interior for one floor pan and carpet. Have just begun the console, seats still in. There are no screws in the front that should come in from the sides into the mounts. Found the two center screws from...
  20. 6

    Carpet thoughts

    I have only done this once, on an MGA and the carpeting was very thick. I used the dyna mat under and had plenty of feel to the carpet. I wanted to get some thoughts from those who have used the ACC carpet. I got a couple samples in 515 and 615, one larger loop and a bit thicker. Comments...
Back
Top