Search results for query: *

  • Users: Carl K
  • Content: Threads
  • Order by date
  1. Carl K

    SOLD 4X 15 x 6 Road Wheels in San Jose, CA

    I have a driver quality set of four Chrysler Road Wheels for sale. The chrome on the wheels is nice. The centers could use new silver paint. These have correct trim rings but the centers are AMC. Some pits, dings, scratches on rims and centers. One bend on one outer rim lip, but the tire...
  2. Carl K

    For Sale 65 66 Chrysler Trunk Lid Torsion Springs with Rollers

    Nice set of used rear trunk torsion bars, with center clip and both rollers. $20 plus shipping from California. thanks, Carl
  3. Carl K

    1965 New Yorker- new springs for towing

    I had some time last weekend to install the new springs I had purchased from ESPO (Springs and Things). The originals on my '65 New Yorker were flat, in fact they had reverse curvature when the gas tank was full. Note this is without the trailer attached! Here's how the rear wheels looked...
  4. Carl K

    For Sale 4x NEW American Racing Torq-Thrust D Wheels 15x7, 5 on 5.0 (Imperial)

    I have four brand new in the boxes American Racing Torq Thrust D wheels to fit an Imperial. Bolt pattern is 5 on 5.0 inches. Wheels are 15 x 7". Backspacing is 3.75". These come with the center caps, plus 20 new lug nuts (1/2-20) and four new chrome valve stems. This bolt pattern also fits...
  5. Carl K

    For Sale Set of Four Late Road Wheel Center Caps - Driver Quality

    Here's four decent driver quality road wheel center caps. They have some pitting of the chrome and a couple have minor damage where the attaching screws were overtightened. One has had the cap spring "spider" rivets replaced with screws. $150 inc. shipping in the continental 48 states...
  6. Carl K

    SOLD NEW Heater Valve for '65-'68 C-bodies with Air Conditioning

    I wound up with an extra NORS heater control valve for '65 to '68 cars with AC. It's brand new old stock EverHot brand. P/N H1279. $125 plus shipping (probably around $7.50 in the US). thanks, Carl
  7. Carl K

    Maiden Voyage as a Tow Car

    The Chrysler finally had a chance to show her stuff as a tow car. After a busy week of changing the differential and new axle bearings, it was ready for it's maiden voyage. A nice, easy 150 miles to Pinnacles National Park near Hollister, CA. Despite the stance in the photo, the car did sit...
  8. Carl K

    Axle spline damage

    Can I go ahead and put this axle back in? My car has the stock 413- not a performance engine. I didn't find the missing part in the banjo when the diff was out, but I haven't looked in the axle tubes yet. One axle bearing looked good but the other axle bearing showed signs of rust and...
  9. Carl K

    Springs on my '65- how bad are these?

    I've got the 75 lb trailer hitch mounted on my '65 New Yorker now. I've also got about 120 lbs of car parts in the trunk (my '73 spindles and brakes I have not installed yet). Here's what my leaf springs look like. Is it normal for 50 year old springs to be flat or even with inverted...
  10. Carl K

    1965 Chrysler Tow Hitch Fabrication

    I've finally finished with the tow hitch for my '65 New Yorker. I used the general layout that Chrysler provided to the customers who ordered a tow package. I didn't want to weld it to the unibody, because knowing my luck I'd need to drop the gas tank. I also wanted to drill as few holes as...
  11. Carl K

    Towing- brake controller and extra gauges

    Continuing in my quest to get the 1965 New Yorker ready as a tow vehicle, I took advantage of the fact that I was already deep into the dash for the radio upgrade to do the wiring for my brake controller and extra gauges. I knew I wanted an oil pressure gauge and a temperature gauge to monitor...
  12. Carl K

    Dash speaker size? '65/'66 Chrysler

    Do you know offhand what the size of the speaker in the dash of a '65/'66 Chrysler is? I'd like to have a dual cone replacement on the way before I take out the old one. thanks! Carl
  13. Carl K

    Aux. Transmission Cooler installation- 1965 New Yorker

    I'm slowly getting around to configuring my 1965 New Yorker as a tow vehicle. I searched the forums but only found one transmission cooler installation- bluefury361's installation of a factory cooler. I didn't have a factory cooler to work with, so I bought a new Derale 13504 fin and plate...
  14. Carl K

    SOLD 1965 Chrysler New Yorker Wheel Covers (Hub Caps) - Set of Five 5

    Here's a set of five driver-quality wheel covers for a 1965 New Yorker. I can't use them anymore since I went to 15" wheels. One is very nice, four are decent. Some scratches at center ring of stainless part. The plastic centers are not cracked. Three out of five are missing the spring ring...
  15. Carl K

    For Sale plymoth fury 3 1973 - $2200 (stockton ca)

    Found this one while searching for "moths". 1973 plymoth fury 3 millas 66000 Tel 209-518-3757 http://sacramento.craigslist.org/cto/5285045130.html
  16. Carl K

    For Sale Road Wheel Center Caps- early and late style

    I have some orphan Road Wheel center caps. Two are the early style, one is the late style. Early style caps each have a dent on the side and scratches on the face of the "gear"- some bozo walked thru the yard and hit each with a hammer. The late style is in nicer shape but does have a dimple...
  17. Carl K

    WANTED 1965 New Yorker Door Panel Wood Trim Insert

    I'm looking for a single walnut door card insert with metal frame from a 1965 New Yorker. From a front or rear door armrest. It needs to be in good condition. I don't need the entire door panel. thanks! Carl
  18. Carl K

    Help! Pulleys and water pump for 1965 with Trailer Tow package

    As you might recall, I am trying to re-create the towing package for my 1965 New Yorker with stock 413 engine and factory air conditioning. Does anyone have this on a '65 or '66 who could share a picture? I'd like to see the relative diameters of the water pump and crankshaft pulleys...
  19. Carl K

    For Sale '79 Chrysler 300 Aluminum "Road Wheel" 15 x 6

    This is an aluminum 15 slot "Road Wheel" as used on 1979 Chrysler 300's and probably others. Sorry I only have the wheel, not the plastic trim or center cap. Very light- only a kiss over 13 lbs. It is a welded, two piece wheel, 15" x 6" with 4" of backspacing. There is still some anodizing...
  20. Carl K

    WANTED Heat Riser for 413 engine

    I need some parts for the heat riser on my 1965 413 engine. The factory kit is part number 2525081- pictured below. I'm looking for the bi-metallic spring and the tension spring, as well as the thing that looks like a pad on a spring steel arm. My riser is free but missing those parts. One...
Back
Top