Search results for query: *

Hey All, I think this car's been posted about before, but it's up for sale again. 1966 FURY lll with 383 4 speed with factory AC. Here is the link to Facebook Marketplace - hopefully the link works... If the above link is disabled, try this but remove all spaces prior to pressing enter...

Hey All, I have two little dogs that wear harnesses and tethers when taking them for rides in our modern cars. Their tethers clip directly into modern car seat belt female buckles, but do not work on our vintage Mopars with airplane style lift-to-release female buckles. Does anyone know of an...

1966 Dodge Monaco Hopefully the issues with Facebook posts are still solved, and people can check this out. Looks like a nice one - basic Canadian Monaco.

So - further to the saga with my AC vacuum switch and blower motor issues - I bought a cheap ampere gauge to measure the load and startup spike of the blower motor in my 66 T&C, since I was thinking that it was on its way out and drawing too much power, and had subsequently melted/overheated the...

Hey all, With these 4 and 5 button vacuum controllers for heat/defrost/ac, it's my understanding from the articles I've read that there are plates that slide back and forth to allow vacuum to be applied to certain pathways within the system. Picture of a non-AC vacuum switch disassembled...

The NSS on my wagon has been acting up, and I finally had to resort to grounding it out, which of course is not the safest thing. I sourced a correct NOS replacement (it was actually kind of hard to find), but I thought I'd ask a few questions here before I go ahead and swap it out. 1) It...

Hey All, Looking for NOS or good used for the pushbutton vacuum switch for a 1965 or 1966 Chrysler and also for 65/66 FURY. The part number is 2587 564 If you have one, but don't want to take it apart from the actual dash HVAC controller, I'll take the whole shebang. Why not buy one of...

Oh fer f's sake! Getting ready to go to the WPC meet and my fuel tank in the 66 T&C wagon shows a leak. What's the interchange ability on wagon tanks, 65-68?

Hey all, I think I know where to look, but it's going to be a PITA to do so. Here's the symptom: When I run the AC in my 66 T&C, it goes fine for a while, then all of a sudden, the blower stops. It might start again, then stops, start again, stop... and then it's done until the car cools...

Hey all, Just for a laugh, I filled my 66 T&C up with local airport gas - 100LL (100 octane, low lead). I'm not being silly am I? Am I going to hurt anything? The car seems to really like it, no more pinging on mid to high speed accelleration, and the idle is smoother. Just thought I'd...

Hey All, If anyone is coming up the the WPC National Meet at the beginning of August and happen to be going fairly close to Columbus OH, I'm looking to see if anyone can pick up some wheels for me from @Zymurgy. PM me please.

Hey all, Still looking for the driver side lower trim for a power bench seat. 1966 Chrysler. It's different from a manual bench seat in that Power seat has a hole for the switch stem, while manual seat doesn't. Anyone have? See the pics below - Power bench seat in burgundy 4 door town...

Just an FYI for all FCBO members, but especially for our Western NY and Ontario members: The Walter P Chrysler Club is holding their 2023 National Meet in niagara Falls NY, Aug 2 - 6. Details to follow, but from my own experience, it's always a blast. I have given Craig @mobileparts an...

@FURYGT - hey Bill, I saw in one of your posts recently where you talked about using a ballast resister that is better for electronic ignition systems. Please clarify, as I'm interested in seeing if using the original ballast resistant in my charging circuit yes circuit is part of the issue...

NOT MINE For those looking for the elusive lower trim for the 68 Monaco 500, here it is it is. It is not mine. I saw this on Facebook, so you should attempt to find it on Facebook as this link may not work. Whenever I try to post a link to a Facebook post, it shows up here as "This post is...

NOT MINE For those looking for the elusive lower trim for the 68 Monaco here it is it is. It is not mine. I saw this on Facebook, so you should attempt to find it on Facebook as this link may not work. If the link shows up as "This post is unavailable..." etc, copy the text below it into a word...

Hey All, I recently got a really decent deal on a Purple cam - according to the guy I bought it from, it's part # P5007 697 It has these numbers on the shank: I think it says 1103 I've been able to find out that this cam apparently has the following specs, but I could be wrong. Can anyone...

Hey all, I am looking for the lower molding for the bottom of the seat that is specific to power bench seat. It's different than manual seat, and not the same as bucket seats either. Look at the picture below - I am not sure if they're the same for 65 and/or 67, but I know that they changed...

Hey all, While I haven't checked my wiring to be sure, I may need a new Neutral Safety Switch for the 66 wagon. Surprisingly, I have not found any on the typical part store websites, my regular supplier says his vendor has stopped making them, and I'm starting to feel like I'm striking out...

71 Fury clutch and brake pedal setup. I don't know why I can't share the FB link to the actual ad, but the seller is named Dodge Stokes. Facebook He's got these parts listed on C Body Owners and Fanatics.