Search results for query: *

What is the easiest way to remove the dash light panel? Do the lamp sockets come out or is there a disconnect for the Orange wiring? I’m troubleshooting an issue with my dash lights not working and I think the panel is not grounding properly so I am going to sand it down. It would easier to...

Hi Everyone, Normally I would not post a question about a car other than a Mopar on this site however I feel that the collective knowledge here is far better than what is available through other online resources for this type of vehicle. You guys know a lot about auto mechanics so I'm going...

Summer is here so it's time to look at getting a fan shroud for my 1972 Fury III. The car never had one but there are mounting holes on the radiator - spacing is around 11.5" from center to center - top to bottom. Radiator is 26" and the engine is a 360 small block. I see a lot of options...

So I've decided to go ahead and get my exhaust system replaced on my '72 Fury III (360 engine - single exhaust) and I was looking to get some feedback on the estimates I've received. Pipes are pretty rusty and I've had to sleeve a section where it has a leak. I've also got some funds...

I often like to share my successes so why not share my failures too? My wife's 2008 Town and Country van needed a new CV half axle. My brother helped me do them on my 2001 Pontiac so I thought I could handle it on her van and save some money. Seemed simple enough... Well I couldn't even...

As typical with a Fuselage my rear window reveal clips have rotted away so I can't really tell what kind they are. Tried looking in the FSM body manual but I could not find any information on them so....I bought what I believed to be the right clips (NOS Chrysler Dodge Front Windshield Rear...

I am just wondering what everyone's thoughts are on outfitting the rear seats with shoulder belts. My '72 Fury has only lap belts in the rear seats....it has shoulder belts for the front which looked like they were never used until I got the car. I have 3 kids and I like using the car to...

So this spring I would like to deal with the surface rust that is mainly on the lower portion of my car ('72 Fury). See pics - this is the passenger side. The driver's side has it too but it is not as bad. I can't afford to do a full repaint on the car and I don't really think it needs...

I'm wondering what the brain trust of FCBO thinks about this - good? bad? I myself am on the fence...I think it's inevitable but maybe not for me. Digital license plates that cost whopping $499 now an option for Arizona drivers

I'd like to replace some of the hoses on my '72 Fury but I'm not exactly sure of the sizes. Can someone tell me what sizes are the following hoses? Brake Booster hose PCV Valve Vent Tube hose (from charcoal cannister) - this one has a red stripe on it - goes to a tee that has two larger...

Let's all have a laugh at the expense of the younger generation. I know my kids make fun of me when I stumble at new technology...watch the tables get turned.

So according to the FSM, the crankcase inlet air cleaner should be removable from the valve cover. However I've been tugging and pulling on it but it doesn't want to budge. What's the trick here?

These are parts I replaced on my 72 Fury about a year ago. Is there any use for them? Is there a place that will take them to get refurbished or should I just toss them?

A house down the street was giving it away. My wife spotted it and thought it would be great to give my daughter for her third birthday today. Cleaned it up, got a new battery and she loves it! Definitely in better shape than the ‘76 Eldorado convertible I once owned. At least this one is...

My 72 Fury has these mud flaps on it. Would these would have come original with the car - an option perhaps installed by the dealer or is it likely someone put them on afterwards? I am thinking of removing them if they are not original.

I am wondering if anyone knows about these tire pressure monitoring systems (TPMS). Long story short....my wife's mini-van (2008 Chrysler Town and Country) needed a tire stem replaced. The threaded part was broken and since we are taking a 900 mile trip to Florida tomorrow I thought it...

This is an annual Father's day car show held in Chantilly VA at the Sully Historical site. Might be the largest car show in Northern Virginia. It is co-sponsored by the Model-A Ford club of America. The heat was brutal and the food prices high but there was a good variety of cars. Event...

Just wanted to get some thoughts on what to use for this hole near where the seat belt attaches. Fiberglass patch or body filler? Welding is out of the question since with my skills I'd probably make the hole bigger. Thanks

Since I've started driving my Fury the odor of the interior is starting to wear on me. It sat in a barn for ten years before I got it and it looks like mice had been living in the headliner. I didn't realize how bad it was until I took a trim piece off and mouse turds started pouring out...

So after sitting two days at the alignment shop the mechanic called me and said he can't do it. Not exactly sure why.....he didn't say. Maybe they don't want the liability. So....any suggestions in the DC area for someone that can do an alignment on this car? I am going to try a local...