Search results for query: *

Hey guys, It has been a while, hope you are all doing well! Now that I am in college, I don't have a ton of time for the NYB, but I have been helping a neighbor who fought in Vietnam as he tries to sell his 1975 Chrysler Cordoba during my breaks. I had a few questions: 1- I will post pictures...

Hey guys, A new problem popped up today. I hit the left signal while turning and it just stayed on for a while. Eventually, it started blinking, but only like one blink every 45 seconds. Right side works fine, unable to test hazards as my switch is broken so if I pull it out I have to reset...

Needed for 77 NYB, due to turn signal switch install Thanks, 77newyorker440

Does anyone know how to remove the horn pad in a 77 NYB with the tilt/telescope two spoke wheel? Trying to be very cautious cause it is hard to replace if it gets broken Thanks, 77newyorker440

I have been thinking quite a bit about my Chrysler's drivability problem, and after some time, I have come up with a few ideas. For context, it currently runs pretty good with the throttle open, but it has substantial off idle troubles, with stumbles and backfires. This is especially bad after...

Looking for a turn signal/hazard switch for a 1977 New Yorker, Part Number 3747202 Thanks, 77newyorker440

Good Evening Guys, The car is back to having electrical issues. I parked it on the street today and had to leave it for a few minutes, so I left the hazards on. When I went to disengage them, the switch felt quite mushy, and the hazards turn off everywhere except the driverside front fender...

Good Morning Everyone, I have a few questions about my wiper system. Following your recommendations, I pulled the entire system and replaced all the bushings (I've actually done it twice now and am able to do the whole system(from removal to reinstallation) in about an hour, quite proud of...

Good Morning Guys, The 77 440 now will not start after getting a new carb and ignition system. I tested for spark at the plugs, plenty of it. I'm thinking this is a timing issue. Does anyone know what the tdc mark looks like on the balancer, I seam to just have a few identical lines spaced...

Good Afternoon, As shown in the picture below, this new tq has quite a few vacuum ports. Which one is for vacuum advance, and what are the others for? Including the bizarre one on the 45 degree angle. I know the large on in the middle is for the PCV. Thanks, 77newyorker440

Good Afternoon Guys, Working on installing brand new mopar ignition system and the plug for the harness does not seem to match up with the ECU. Anyone experience this before? Thanks, 77newyorker440

Good Evening Guys, Thanks for the advice, I'll be going with a thermoquad. My plan is to purchase a nice, working one off someone here and then ship my current one to @Dana, giving me a car to drive and him plenty of time to work on it. Would anyone happen to have one of these carbs in good...

Good Morning Guys, I hope everyone had a Merry Christmas and a Happy New Year!! My Chrysler unfortunately did not, as all of the sudden, it has begun running extremely poorly, backfiring, bucking, and stalling constantly. Due to this, I think it is time to get rid of the lean-burn system...

Good Afternoon guys, A few questions about the wiper system in my 77 New Yorker. Got the system back together and reinstalled it in the car. Now we are attaching the arms and testing them. However, we noticed that the blades' range of motion goes lower on the body than when the blades are...

Hey guys, I have some questions for you all about the Carter Fuel Pump before I go ahead and install it. 1) Should the lever on one side of the pump move? Cause mine moves maybe 1/2 of a millimeter total with small force applied to it (I did not want to break it, just see if it moves). 2)...

Good Afternoon, Recently my dad and I took the Chrysler out for a ride and noticed a wet spot both on top of and below the fuel pump. At first, we presumed it was the rubber around the filter so we replaced that, but we took it our again and it was still wet. Then, much to my...

Hey guys, When I open up the forums, there is no homepage anymore? Does anybody else have this problem? The rest of the website works completely normally. Thanks, 77newyorker440

Hey guys, I am currently working on learning how to set timing while my carb is out with @Dana, and I wanted to check some things with you guys. 1. What does the lean-burn do to timing? I have heard that it retards the timing when you accelerate but are there any other effects? 2. A friend...

Hey guys, I am in need of your all's help and knowledge. The New Yorker is at Carlisle and is having some idle/driveability issues. It just started on this trip up but got progressively worse today. Here is the problem: When you just slightly tap the gas, it stalls out completely...

Took the New Yorker to the Dyno, results were pretty interesting and are shown at the end of the video Hope you enjoy! 77newyorker440