Search results for query: *

I have almost completed in my recondition/paint of the 300 grill. Going on about 12 hours and 80% done, not wanting to do this again. Oil based paints applied. An effective traditional wax and buff would be difficult due to the corners and small spaces. Given the intricate design, was...

Have been trying to repaint the black insert lines on my 68’ 300 grill. Have tried a liquid tape product called Peel-tek with no success. Doesn't trim worth a darn. Have tried lightly brushing and then heavier. Seems to come off in pieces or in strands. Anybody had any success with this...

Would anybody have pictures of the front windshield support with the top down (best) to see what I am missing or should be looking for? When I sent this car for repaint, I don't think I received all the trim pieces back as they kind of lost they're, well short staff, short story.

Its been about 5 years since trying to get this car reassembled and I have lost or misidentifying the bumper mount bolts. Thought they were 1/2-13x1" however found pictures that showed the two supports per side are, or seem to be, bolted together which would make the 1" too short. If anybody...

It’s been some time(years) since I disassembled my 68’ 300 bare for complete redo. Recently repainted and going through bags of parts, I came across a bag that says “300 dash”. I recognize the parts but cannot place them. Help/suggestions appreciated.

Have an extra set of HP manifolds and will be refreshening my 73’ Imperial. Would anybody know if they will fit? Thanks.

Would anyone know if the 68’ cornering light lenses would fit a 67’ Chrysler cornering light frame and bezel? A parts box that came with my 68’ has, what I have learned, are 67’ cornering mounts and lenses with not so great lenses. The 68’s are more readily available.

Would anyone have daily driver kind of “CHRYSLER” lettering for the front hood? They are about an inch high. As well, seeking the “THREE HUNDRED” emblems mounted on the rear quarter panels. Thanks.

Need help. Needing the rectangular retaining clips that go on the, I call them fender fish fin trim, pieces on the 68’ 300. Also, are there any vendors that supply the window rollers for a 68’ 300? Some are seized and perhaps he persuaded with some TLC but are there any sources out there in...

Would anyone have a picture of the drivers side, (under hood) fender where the factory cruise control would mount? I have two mounts and different servos so not sure what should be mounted where. Car did not have the option when I purchased the car so either no mounting holes or none that...

I could be wrong however I remember our 75' Imperial had a mesh material on the package shelf (above the rear seat). It covered everything so well, you could not see where the speaker slits were. Very professional, high class in my mind. Is this available or can somebody better describe it...

Has anybody had any success is finding a source these gaskets? DMT does not seem to have and waiting for a reply email as sometimes not all their products are listed. Thanks.

If available, what vendors might be selling these? I believe are only under the front and rear quarter panel extensions where it meets the bumper. Thanks.

Looking for 2 sets (throttle and kickdown) of springs or if someone has a box of springs they would like to sell. Am working on a 67' Imperial and 68' 300, both 440's. Been working on so long, have lost my springs. Thank you.

Not sure what these would be called, levers for 68’ (I’m sure other years) power window switch? Are these available anywhere? The ears have become weak which lodges the lever (paddle) sideways.

Did the 68’ 300 offer electric locks? I remember the push/pull feature in Chrysler models but not sure of year. If it was not offered in 68’, is it possible that add the push/pull system to the 68’ 300?

Anybody have a recommendation for a convertible top for a 68' 300? Not sure where or why I have a note for "Convertible Top Guys", but they don't seem to list a 1968 300, unless I missed something. Thanks.

Sorry, not a Mopar part and this is a long shot. I am seeking four base plates for the filter. Holley sells right and left side filter cover plates and will make a phone call for the base plates. I purchased these from a fellow not realizing the bases were not original. Probably revised for...

Tried the online decoding quips and indicates a Chrysler 300 Manual 4 speed. Would like second/expert opinion. Thanks.

Planning to do a refresh on my 73’ Imperial. Manual says 8.2 compression on the 440. Would a 906 head be an upgrade to bring the compression up to say 9.5 or is there another option/recommendations? Thanks.