Search results for query: *

  1. C

    WANTED "High step" jets and 3 step rods

    I bought one of the old Carter Strip Kits for my '70 Monaco 383 4bbl AVS to explore with. The "high" jets and 3-step rods. When I got my '67 Newport 383 4bbl AFB later on, I tried the 3-step rods in it. Same length as the AFB rods. I could tell no difference in any performance parameter...
  2. C

    WANTED 4160 carb washer

    If you have an idea of the ID and OD of the needed washer, you might head to Lowe's and look in their nut/bolt/etc. selection for a washer of the desired specs. Some larger auto supplies and hardware stores have similar selections, by observation. CBODY67
  3. C

    WANTED 4160 carb washer

    Looks like you ALSO need a correct balance tube with the expanded areas on them to retain the balance tube o-ring seals (as pictured). OEM tubes were textured aluminum, or similar, not brass. You can probably order them from Holley, but they were on all 4160 4bbls regardless of application...
  4. C

    WANTED Wanted Original 1968 C body Trunk Mat

    Agree with the above as to "50+ year old trunk mat". On the Chryslers, the lower-level models (as Newports) had a thick, molded-pattern rubber mat. Rubber got old and brittle. Moving them disintegrated them, by observation. Replace with carpet from New Yorkers, with the correct side...
  5. C

    WANTED Carter 3 step Metering rods for 64 Imperial

    The first thing I reacted to (when I saw your post) was the request for 3-step metering rods AND you had the dimensions for them (which are not in the factory service manual). Typically, AFBs had 2-step rods, but the '63 FSM illustrates a 3-step rod. Prior to this, I was under the presumption...
  6. C

    WANTED Carter 3 step Metering rods for 64 Imperial

    Which Carter 4bbl is on the Imperial now? What operational issue are you seeking to make better? Just curious, CBODY67
  7. C

    WANTED Cruise control

    Hope you recently put new spark plugs in the motor as the servo takes up some valuable real estate where "arms and hands" might need to go on the lh side of things. Unless, of course, if the best route is with the car on a lift. Just a thought, CBODY67
  8. C

    WANTED Intake + Tires

    P225/75R-14 tires have been decreasing in availability since the earlier 1980s. Might be some in the Hankook (possibly whitewalls) and Nexen brands. If you are only needing a spare tire, then buy a NEW one rather than an old one. ANY tire of that size, used, will have been aged-out of...
  9. C

    Found 1966 383 2v air cleaner sticker

    The one on our '66 Newport 383 2bbl is the more common yellow-orange rectangle sticker. Which have been in repro for quite some time. As I recall, from back in the 1970s or so when I was looking for one (though not really needed), the 4bbl items had very minor differences in the wording, but I...
  10. C

    WANTED Stromberg WWC 3-262 carb

    That was my first attempt at compensating for "the warp". Even added a bit of clear silicone in the middle. When exposed to gasoline, the silicone swelled, but still closed the gap in the vacuum to the power valve. I had to replace it a few months later, though. Second time around, I used a...
  11. C

    WANTED 70 Rim Blow steering column components

    That looks suspiciously like the one that is on my '70 Monaco Brougham tilt wheel. There should be a recess at the bottom, behind the wheel's center, that is cast but not machined for the telescope lock lever. The center trim piece is the same, too, other than mine has a "DODGE" name on it.
  12. C

    WANTED Stromberg WWC 3-262 carb

    As much as I like the WWC Stromberg, it does have some issues . . . like the air cleaner stud, being over-torqued for years, will pull that part of the air horn upward, which compromises the seal of the float bowl to the air horn. Other than fuel being sucked out of the float bowl when the...
  13. C

    WANTED Wanted: Dodge Chrysler Plymouth Mopar Engine Mount cable

    The GM (Chevrolet-specifically) add-on kits for their cars and pickups, starting with the middle 1960s cars, until about the 1970 model year, as I recall. What was in the kit varied with engine and model of vehicle. So although they all had a cable it them, the other items were model-specific...
  14. C

    WANTED 70 Rim Blow steering column components

    First, I wish you well in your quest. You could have used a Dodge or Plymouth tilt column (no telescope) rather than the Chrysler T&T column. I am NOT a fan of Rim Blow, from my experiences on my '70 Dodge Monaco Brougham DH43. I am considering options to swap to something else so I can have...
  15. C

    WANTED Stock Steel Wheels

    As they are repros, I believe the WV items are claimed to accept all factory caps/covers, by them.
  16. C

    WANTED Stock Steel Wheels

    Otherwise known as "cop car wheels". Wheel Vintiques has them, too, or used to. Check www.summitracing.com, too. Look for the best price or any sales this time of the year.
  17. C

    WANTED 69GE 4001,4002 wide flute headlights

    Are what you're seeking the normal 1969 model year low-bean and high-beam headlights, rather than the later versions of those same numbers? Or does "wide flute" indicate some other specialized beam pattern than the normal low-beam and high-beam headlights? Just curious, CBODY67
  18. C

    WANTED Hughes Performance 727 19 SPL 2500 INT

    Can you get the Tracking Number for your shipment and check the progress via the FedEx online website? Contact the shipper for that information.
  19. C

    WANTED Maps-Light Chrysler 65

    Looks like the sample (in the picture) has the typical crack on the lh screw hole. Reason I say "typical" is that back in the earlier 1970s, I bought a new lens from the dealer as the one in the car had that crack in it. I carefully tightened the screws and that last little bit cracked the new...
Back
Top