Search results for query: *

Hey did you figure out anything on this swap as to whether or not it will work?

My 67 Polara 500 convertible carried j4 code for body sill molding, even though that molding was standard with the 500 package, and runs along with wheel well moldings. My 67 Polara 4dr carried j4 code for body sill molding, and that was an optional 1.5" wide molding that ran the length of the...

A few additions from my opinions to populate the list. a6 -console b5 -bucket seats? d6 - h7 -fender or hood mounted turn indicators j4 - body sill trim moldings k7 - u1 -sold car when built A1 -26 inch radiator H2 - J4 -power left hand seat K8 -power windows R2 - radio (Astrophonic) S1 -air...

On mine I replaced the leaf springs and hardware, so I did not have to worry about that (mine may have fallen out of the bushing anyway) but on other makes if tapping them out with penetrant-soaking does not work, I sometimes chew through the rubber between the spring eye and the bolt with an...

This is why I enjoy Motor's Manuals so much. They each cover a 7 year period. Back in the day, before Al Gore invented the innernet, one could run home and go to the fine literature on their bookshelf to figure out what they just seen in traffic. You can get them on ebay now. I would spend hours...

I do not know about whether or not it locks. It is possible that the latches have taken on a side load if the quarter panels were wanting to splay outward once the structure is cut away (you have already tested for vertical movement with the jack). I would now establish what the measurement...

I have three Polaras, a couple of Pontiacs, a chevy, an International Scout, an Accord daily driver, and even two Ford pickups (no shame in it). I love pretty much all domestic cars from the 60's and 70's with the exception of the AMC Matador. Those things were sure fugly.

https://www.motortrend.com/how-to/mopp-1204-c-body-sway-bars-roll-control/ https://firmfeel.com/ https://p-s-t.com/

Looks like I got Inspector 74.

Yes, it has a LH power bucket seat. Thanks.

Oh... thanks! I am learning so much from this thread. Anyone know what abc: m3, and ABC: W3 and J4 are?

Light green metallic Windsor Ontario Polara 4 door sedan: DL41G7913XXXX. November 25. Also has the upper body mouldings around the sedan side window frames, forgot to mention that. White Belvidere Polara 500 Convertible: DM27K7414XXXX. November 11 Red Belvidere Polara 2 door hardtop...

In this example, the w8 from the light green metallic Windsor Ontario Polara 4 door sedan: PAINT: Monotone Light Green Metallic Paint. OTHER: Black Upper Door Frame Color. MOLDINGS: ABC OPTIONS: Also Has power steering R1: AM...

It should have mouldings like this car, with the standard Monaco package.

j4 is the lower sill moulding. I have seen j4 show up on both a Polara 500 that came standard with a lower body moulding/wheelwell mouldings, and also a Polara 383 that the optional lower moulding was ordered ala carte. According to the service manual, upper and lower case abc options "INCLUDES...

I used a Holley red pump, which does need a regulator. I also installed a relay under the dash. Next time I might use a Carter electric. This is a workaround for today's bad gas formula. When I shut the engine off the fuel boils out the float bowls causing the engine to flood while...

Please look at the wiring to the roundels, and get back with us. Is that part of the original harness? Look at both the engine compartment, and in the trunk.

Look for a build sheet under the rear seat bottom tucked into the springs, or inside the driver's side seat back.

And another thing. My Canuckian built car had the front steel fuel line segment that runs from underneath the passenger front floor up to near the engine not routed through the front frame rail, and emerging through the frame again at the front; near the fuel pump like my Belvidere New Jersey...

Another possible roundel car. I am not seeing the bezel though. Need more pictures of this car.