Search results for query: *

I need one 1969 Chrysler 300 tail light lens. used with minor cracks OK. right and left are the same I think. It's for a wall hanger assembly so cheap is good.... Thanks Will.

A couple of things needed for a 1961 Fury convertible. I need one shoulder bolt for the folding top frame. it has a thin profile hex head, then a shoulder that passes through a main rear top support brace and a fine thread stud. There are four per top, one of mine got legs. Also need a carb air...

We had a mishap and now need any and all moldings and trim for the left front fender on a 1968 Plymouth Fury VIP. Wheel opening molding, side trim, headlight molding, etc. Any help would be appreciated. Thanks, Will.

I need a left rear manual window regulator for my 67 Polara convertible. The parts book shows all 67 C body convertibles used the same part number, (2802220-1. Not sure which is the left, 0 or 1). I have to think a 68 would be the same but can't verify without a 78 parts book. I appreciate any...

I need a nice rear window crank for my 67 Polara. It seems the splines where it mounts to the regulator are weak and it starts to skip when at the extreme top and bottom position. Fits all A/B/C bodys # 2802842. (Marty has one but can't ship till June). Thanks. Will.

Looking for a left front turn signal housing and pigtail for a 1967 Dodge Polara. Very good or NOS. I believe a 68 will interchange. Must be a left side. My left side signal works but on the dim side of the bulb. L & R Housings will interchange but the plugs are orientated different. Thanks Will.

I need one 14 x 5 OEM steel wheel for my 1961 Plymouth Fury.

I need a dash map light for my 67 Polara. My lens is fine so just a bezel with switch will do. Not sure about the crossover with other models is. thanks Will.

I need a Mopar OEM radio suppressor part number 2884869. It mounts on the coil bracket. used on 67 into the 70's. The part number is stamped on the end of the can. A clean used one is fine. Thanks Will.

does anyone have a push rod for a 67 383? Will.

I need a good vibration damper to fit a 1967 383. I think 65 to 69 will interchange. Thanks Will.

I need a right side tail light lens, (only), from a 69 Chrysler 300. A crack or minor damage is OK. Will.

1967 Polara 500 driver side bucket seat. lower side at adjustor. It may cross over to other years and car lines. This one works but is a little rough, I'd like to replace it. Thanks Will.

I need a decent rear seat speaker grille for my 67 Polara. I believe 67/68/69/70 Plymouth, Dodge and Chrysler C body convertibles are all interchangeable aside from the emblem, which can be switched. I'll post a picture a little later.

I need a jack hook for my 67 Polara. Looks like this......

Has anyone got a antenna base gasket for a 67 Polara? Fits between the antenna base and the fender. Thanks Will.

I need a right side vent window regulator for my 67 Polara. part number 3824304, stamped on the part. 65/66/67 .... same. Not sure about 68. Thanks Will. PM here or [email protected]

1967 Dodge Polara right front wheel opening molding. The section over the top of the opening and forward to the bumper.

Disregard this post. It's suppost to be that way. I just discovered that, (for reasons unknown), there is a small hole drilled in the driver side door glass on my 67 Polara convertible. (pictured in my thread in the slabside section). SO..... I'm looking for a clear, driver side door...

I need a dash ash tray mount bracket for my 67 Polara. I'll buy a complete assembly if nice. Perhaps a 68 will work? Two of the four ball bearings that the tray slides on are missing. Thanks for any help. Will.