Search results for query: wiring harness

NOS Trailer wiring harness for a mopar. Complete and never installed. 75.00+ Shipping

Start a Parts wanted thread. Marketplace forums for aused harness or where to buy a new one if available. Repairing harnesses is as easy as replacing damaged wires or connectors.

A complete rear defroster with the wiring harness, motor, outside vent bezel and a new hose with clamp. Comes with the speaker grille with mounting. 200.00 + Shipping

Thanks for this Vaanth, appreciate this. I may just get a new 4 wire harness & box, instead of finding the correct way to wire the 3 wire harness with the one I bought previously (a few years back). This diagram is fine, but the wires to the distributor, are not part of the provided subject...

Thanks Gary, I just called hot heads and they have my buying history and confirmed I got the whole enchilada 5 or so years back, including the small block distributor, distributor extender, Chrysler orange box and 5 wire harness ( I loosely refer to this as a 4 wire harness as 1 wire is not...

...snug! Had to install the engine by itself. Trans will be in this week just for test fitting everything. No one makes headers for this application in a c body so I will be fabbing my own! Still torn on whether to go with Holley terminator x or the mopar performance wiring harness kit. More to...

That rear body harness diagram is on page 8-125 of the ’70 Plymouth service manual, the OP asked about a ’70. By ’72, some of the body related electrical diagrams were in the separate ’72 Body service manual. It’s my understanding Hamtrack Historical had to pull the service manuals because...

The way I repair a wiring harness is to lay the old one out on a piece of plywood and draw around it with a marker. Then I use finishing nails around the outside of the harness and the terminals. With a few written notes here and there, I then unwrap the harness and change the wires as...

I agree with Big_John & Ross. A factory harness is the best way to go. Using Big_John's method you can clearly see all of the wires in your harness. Unless your harness is severely butchered and / or melted, you can use it and be able to see what wires need repaired or replaced. Solder any...

Try Evans — I have several of their cables, they are correct and their customer service rocks. Evans wiring Engine Wiring Harness

Oh I forgot the engine bay pic. (edit) "This is a project that's almost done the last part to finish is the wiring harness with instructions already partially installed." I wonder if the instructions are from Disneyland seeing that this is a Southern California car? (mickey mouse) .

I know if I just started to tear into my dash, I would probably get my answer but..... 67 Fury II, is it likely the existing wire harness is pre wired for a map light and ignition switch light (pigtails)? Doubt if the fender signals would be but that's a lot more wiring.

The two areas here are the biggest concern they seem to be the only damaged areas of the harness. The black connector I cannot seem to find a way to repair. The bulk head connectors seem to be available Wiring Connectors Bulkhead Fits Mopar Dart Cuda Challenger Charger RoadRunner | eBay.

by doing it in the kick panel I was able to leave the original wiring to the switch intact and only had to add 2 new 12ga hot leads to the relays off the post of the circuit breaker...the leads on the sockets were long enough to splice into the existing harness for the brown and yellow

Thank you

Ok wire experts out there, installing a complete wire harness. Problem wires going to back windows appear to be 2 feet short. And wires going to door windows appear to be 2 ft too long. Wires are in origional wrap. I removed many yrs ago when i started the restoration. All fit well back then.

Do you still have this car? If so I'd be interested in the wiring harness, steering column, dash pad, and inside rear window trim. Thanks, James 469-222-4405

Yes, I have used Evans cables also. Great to work with.

Does your car have the wiring harness to connect to the motor? I've never seen a motor like that before. It's nice looking, but not what I thought a slab would have.

...A/C items. Emission control items. Or is it being automatically condemned due to "age"? Seems like others have mentioned Evans Wiring Harnesses in the past? With the harness removed, it can be a prime time to clean and refurbish the bulkhead connector as needed. Repair terminals ARE...