Search results for query: HOSE!

Six; I was hoping that was the case but the small nozzle and the hose are of vary different diameters. Paul

This is a OEM Air Cleaner To Breather Hose W/Clamps. It is original, not a china knockoff, and is in good condition with no cracks or damage. It came off of a 1969 GTX 440, but is correct for several years and engines. $25.00. Local Pickup, or buyer pays shipping.

Stainless steel braided "anything" line looks neat, BUT that exterior braiding only protects the inner rubber hose from abrasion and such. It does NOT make it a better hose. The rubber inside still needs to be rated to carry fuel. It can still collapse internally after the ethanol-content...

Thank you Vaanth. I will pass this info along.

Did your have a crush washer on the front drum hose to cylinder ?

No I don't use it. New hose and cylinders don't come with them. Disk brake hoses do come with them, but that's because its a completely different fitting (banjo type). Does it matter? It might - it might prevent the hose from seating properly in the wheel cylinder if the washer is too thick.

Rear Brake Hose NAPA 24058 is about .15” shorter than the hose I have that collapsed internally 3/8x24 inverted flare brake fitting fits upper end 7/16x20 inverted flare male fitting fits upper end. I measured .3” depth in distribution block. Length of threaded area of hose fitting is .58”...

Vac hose routing graphics were ONE of the best things the OEMs did, back then. Quite colorful, too. BUT time and heat and such were their demise, unfortunately. MANY were reproduced in the FSM. What I discovered was that if one knew how the emissions item worked, when it worked (hot or...

The bypass hose on the small block Chrysler engine and slant six engine, or the internal housing bypass on a big block engine, allows coolant circulation within the engine while the thermostat is closed. The coolant is pumped against the bottom of the closed thermostat valve when the engine is...

I found out a 4 inch Long rubber hose ( not sure about the diameter) that fits tight on the ceramic insulator is the easiest way to remove the plugs, once they are broken loose. It‘s also a safe way to screw them in by Hand, without Risk to damage first thread Winding. The rubber hose is so...

CB; I'll cap the small nozzle on the vacuum tree but plugging the hose doesn't make sense cause it is going to the vacuum source not coming from the vacuum source. I can't see where the vacuum source is for that hose. Paul

This is a OEM Big Block Heater Hose Bracket. It came off of a 1968 440 with A/C, but may also work on other years and engines with or without A/C. It is original, not a china knockoff. It is not new, but is in good used condition. $15.00. Local pickup, or buyer pays shipping.

Fuel injection hose, SAE specification 30R9, works, but Thermoid makes the conventional Nitrile based hose, SAE specification 30R6 and 30R7, that can handle ethanol bearing gasoline blends, including E85. The following images show the Thermoid catalog listing for these hoses:

Thanks for this

if it has an inverted flare at the bottom of the hole, you don't need a washer...if the hole is drilled straight through and open at the bottom, you need a washer...the same brake hose can fit multiple applications and will come with washers in case you need them which makes the part more...

Do your heater controls work as they should and the hot/cold selector. What doesn't work? Yes put that hose on the tree and see what it does.

I put the UV dye in it and drove it home. After dark I checked it with the UV light and the only evidence of a leak I saw anywhere was a small weeping leak around the heater hose where it connects to the water pump. Nothing under the car and nothing inside. I've seen where a bad coolant hose...

Yes....that is correct. Make sure to ask your jobber for titty sprinkle hose.

Do you use a crush washer on front drum hose threaded to brake cylinder.? Does it really matter ?

The hose going thru the fire wall is more than likely for your heater controls. It looks to me that it should hook up to the nozzle that is uncapped.