Search results for query: *

...garage kept many new parts and well kept. Points ignition system changed over, new battery recent brakes recent tune up new tires new radiator. **When I bought this car I was told it was running but backfiring through the carb, I was told it slipped time, I tore it apart and stopped when I...

New Game to start 2026. Happy New year. i willl try to get a few games in early. Recall, any way you can solve these is fine - No such thing as cheating. OP's only ask that if you get it before official reveal, feel free to indicate you "got it" but please let it run so others get a...

You can use an ohm meter to test the electrical side of the switches first. Ideally, you want to see zero ohms, but anything over 0.3 ohms and they need to be repaired. If the mode buttons on the selector switch are real stiff, it should come apart to be cleaned and lubed. There may be a...

Thanks big John for the link, and marty for the kind and exelent service, I spoke to @Mopar Marty and got the parts ordered, it was a pleasure to have met and speak with such a wealth if knowledge and a great person as well. Happy new year to all.

This ongoing discussion on FABO might be worth a read. Looking into doing my first paint job next year.

IMHO... If it's working, leave it alone. Any "new" reproduction stuff isn't going to be as good. NOS should be better in theory, but realistically NOS stuff is sometimes an expensive crap shoot. If the hoses are still pliable, they will probably last longer than new ones.

believe that's FURYGT

my local PPG dealer had formulas for my DD1 mist blue (68)...most body shop supply stores only carry one or 2 lines of paint so you may have to shop around...my Axalta dealer didn't have a formula for it but sometimes its a case of "somebody tore that page out of the old book"...there are places...

Hella E-code (left) pattern comparison to Holley Retrobright (right)-lowbeam-4 lamp system highbeams Current draw comparison to the Retrobrights

Hi thanks for all your help! Will defo consider all this thanks! Fuel pump and pushrod are both new yes! Thanks

Compression readings are relative to the elevation altitude of the vehicle when the test is done. Most of the specs usually indicate "At or near sea level". As long as the readings are within about 20psi, all is good. When I was "worried" about cylinder wear on our '66 Newport 383 2bbl, I...

Finally got the dash halfway disassembled in my 1965, and found the severed vacuum line that fed to the control block and kept everything from working. While I am in there, I am going to buy a vacuum gun (any suggestions on which one?) and test operation of all the plenum door vacuum actuators...

Glen Elder, Kansas Now a very cool private residence.

Aim and BEAM PATTERN. The ONLY aftermarket LED headlight I've seen with a decent beam pattern is the Holley Retrobrights. Otherwise, check out www.danielsternlighting.com for better headlight solutions. European E-code light housings with good bulbs (all of which are about 55-65 Watts in...

It's my understanding that "deck height" is cut after the crankshaft main bearing saddle "line hone" is done, as it is that place that all of the upper machine work is based on. Then, each OEM-family block has the "deck height" dimension which is measured from the centerline of the crankshaft...

Agreed. There was a mountain of difference in sound between pre-recorded cassettes and cassettes I recorded on quality tape like Maxell or Memorex. None of the high-quality cassettes I recorded are non-playable. Record companies used the cheapest tape and housing available.

NOS rim blow steering wheel. Not sure if rim blow feature works but rubber horn contact is not cracked $300 (obo) + shipping

Seems like there is a member in here that sells the factory look-alike electronic regulators, on eBay?

Axalta, which I believe is the brand that superseded/bought DuPont's automotive paint business, still has a "single-stage" acrylic enamel paint product. GM used acrylic lacquer paint as Ford and Chrysler used acrylic enamel paint, only. In general, many body shops liked to use acrylic lacquer...

In many respects, the 8-track (and probably the prior 4-track set-up?) had a design flaw where the tape would rub against itself, going different directions, as it ran its loop in the cartridge. The malfunctions probably happened when the tape's lube ran dry? Cassettes were, basically, a mini...