Search results for query: HOSE!

thanks

It's a 65 Fury III, this would be the third time it's been rebuilt that's why my thought was to just get a new Federal Style. I think I found the correct bracket, just need the pully and maybe a cap? Also not sure if hose connections will be the same.

I recall when still driving with the single pot on Mathilda I'd failed to properly tighten the driver side wheel cylinder hose properly, and sure as **** lost plenty brake fluid. Thank the Lord, I'm a practiced stopper sans brakes, which I did when the pedal bottomed, using the transmission and...

So does that coiled up bit at the end of the tube just rest on top of your new hose and then you apply the black goop to insulate it?

thanks

I'll have to go and check the size. It may be incorrect but if it is it's also incorrect on the other end which isn't leaking. It's weird that I don't have any other leaks at any of the other rubber to steel connections. It's also weird that fuel flows out of both the vacuum side and the...

That AC hose looks compromised to where its fitting is crimped on. New ones can be made. Finding a good used one that doesn't show swelling and damage in that area will be fine, too. Most of those AC systems were identical for the same body styling years (such as 65-68), with very few changes.

The water pump has been resealed, the thermostat was replaced, the housing, cleaned and painted and the heater hose nipples were cracked loose.

Maybe... not sure... don't have a later car to compare.

This is a OEM Big Block Heater Hose Bracket. It came off of a 1968 440 with A/C, but may also work on other years and engines with or without A/C. It is original, not a china knockoff, and it is not new, but is in good used condition. $15.00. Local pickup, or buyer pays shipping.

If it runs good then go with it. Yep, Mechanics trying to find a customer for their services. You have no idea if the speedo was ever changed or car run with speedo cable off. So don't take the dash mileage as full truth. Ever tried finding 413 pistons? Not that easy today. And if it's...

That's awesome. Thanks Big_John. Great idea.

Pulling the pins from the hydraulic cylinders is probably the best, but another (possibly messy) option is to disconnect the 2 hoses from the pump. Use a hardware store fitting or short hose to connect them back to each other.

On the bench, the air conditioning door actuator can be tested. It appears to be a push/ pull apply vacuum on one hose the rod extends, the other it retracts. The heat -defroster door actuator as reported seems to fail, however when both actuators are connected into the cars vacuum system. This...

Your hose could have a slight blockage in it. There's A LOT of pressure applying the brakes but almost none releasing them. The slightest blockage will cause problems. When at all possible, change everything in pairs. I used to tell my customers you can buy just one sock or shoes. They both have...

Bob, I believe the 62 and 63 413 engines used the same air cleaner. (maybe others too) Yours very well could be original to your car. I only know for sure, the one I have came off of a 63 Dodge 413 engine. Not sure what happened to your snorkel. Maybe someone added a hose or tubing from the core...

This is a OEM 1967-69 Heater Hose Bracket for a Mopar Big Block. It may work on other years and engines as well. It is in good condition. $20.00. Local Pickup, or buyer pays shipping.

Fuel pump pushrod or fuel pump is my bet, but it also could be ignition related. Bad coil or bad pickup in the distributor can do that. Possibly ECU box too. Check the fuel by disconnecting the fuel line at the carb and sticking a piece of hose on the end. Also disconnect the coil wire so...

Have you changed the oil since you had it? How long did istay clean? Is the choke adjust right, or does it blow black smoke when cold? Try this, spray a small amount of atomized water spray from a hose nozzle down the carb with it hot and running 1200 rpm. Do it 5 times about 4 seconds at a...