Search results for query: HOSE!

Part of diagnosis is "try and see", so cap the metal tap on the power brake vacuum tree and plug the other hose. Pre-made vac caps can be found on the "HELP!" racks at auto supplies. Usually in a multi-size cap package. For vacuum lines, golf tees or similar can work. The other thing is "How...

The other 69 Polara I had, fairly original (80,000 original mile), Factory plug wires, belts and lower radiator hose. Original routing? Alan

Yup Im going that route ...and save some pain. Thanks All

Also when you reassemble put some 3/8 hose on the rod bolts when you install the rods and pistons in the block to keep from nicking the crack again.

Well, unfortunately, the last person used heater hose instead of vacuum hose, so it's not correct to begin with.

The old power steering pump is a TRW, it has the big divut in the back and the larger shaft. I've went forward with the federal. It is a whole can of worms for sure. From having to use different pulleys, to bracket mods. Now the thing that is holding me back is the federal pump uses an O ring...

LOL FYI - the hose is a GATES. Too late to pull them apart tonight. Mess with it tomorrow or tomorrow-tomorrow or a different tomorrow. Thx

The listing for rear shock is too short, You should go the longer shock, 24" KG5413 KYB rear. KG4507 KYB front. Install 72 dodge pick up truck rear brake flex hose to allow max drop of axel to remove wheels easy. The listed c-body hose is too short and when you lift car the hose gets stretched.

When you DO get a replacement, DO ensure the lever arm with the float on it matches the length and bends of the OEM sender. Many have posted of their new sender not reading correctly when it is installed. Plus ensuring the special hose clamp at the sender is replaced with a new one or "made...

Does it take the same size hose as the later stuff? The later uses 11/32" heavy wall brake booster hose.

Using your wireless probe, provided the metal in the car body would not deflect the signal, you might wire-tie it to the upper radiator hose and put some heat-shielding insulation around it?

Never have seen that issue. The/any OEM production clamps work fine. I ALWAYS get OEM-level hose by Gates (what used to be Gates Green Stripe, back then), though, to ensure what I get is OEM-level or above. Just my experiences, CBODY67

I installed a aftermarket add on transmission cooler with the lame supplied little fabric in it X pattern type gas line hose, it blew out (split) at over 100+ mph and sprayed ATF all over my windshield at that speed. Use good hose as I suspect at high speeds the pressure can get very high. I...

This is a OEM Big Block Heater Hose Bracket. It came off of a 1968 440 with A/C, but may also work on other years and engines with or without A/C. It is original, not a china knockoff, and it is not new, but is in good used condition. $15.00. Local pickup, or buyer pays shipping.

I am having a similar issue with my ‘69 Newport. Non a/c. I turned the heat on for the first time in 25years. I noticed the windshield fogging over. As I switched from heat to def and back seitching the fan speed I noted stream coming thru the heat vents. When I turned off the heat the steam...

Not just a garden hose but a gas station hose. I think I wanna get hosed again by my little hoser friend who lives down the street.

Just got my rebuilt 727 and 904 (that I may list for sale if anyone is interested) from the shop and now its time to prepare to plop it in. When I was removing the coolant lines I accidentally twisted one of the stubborn fittings but it was for the best since once of the previous owners swapped...

Does the casting have a hair-line crack in it? Agree that the clamp should be on the smooth part of the nipple, with the end of the hose extending just past the clamp. CBODY67

It's either one or the other - unless the can itself is leaking, the diagnosis will be the check valve. Put a vacuum gauge on the one hose (from engine side) and plug the other hose. Run the vacuum up to 15 lbs and watch to see if it falls and how long it takes. The hoses and lock itself...

For some reason both of my 69 Parts Manuals only show Valiant, Dart & Barracuda parts info for under the hood items. Without having it apart are there green o-rings for every hose connection or are some metal to metal flairs? Receiver/Drier - NOS or something new available? Thx