Search results for query: *

Working on my 68 300, got my horns working again, after replacing both horns, now removed headlight motor. I cannot get the 2 screws on the body loose! I did pull end caps as far as I could, looks like inner windings are burned up. Are there after market motors out there or can these be rebuilt...

Gentlemen, working on 68 300, electric window removal. Got the 3 holes precut, ignore the 4th extra hole! Passenger side, took out the 3 bolts, motor still now coming loose. I loosened the one at the bottom left,still wont move motor. Is there something still holding motor. I have the window...

Im wondering what could my problem with my 68 300. It has been charging normal for about a year, battery is a year old, I had the alternator rebuilt about a year ago and Ihave one of those oem looking solid state regulator I got from someone here. I only drive on weekends a little, amp gauge...

I have a question about the window motor on my 68 300. I finally removed the door panel, I dont see much detail in fsm how to remove the motor, passenger side 2dr. Im not sure where to start! Can anyone give any tips on this procedure? Im afraid to start removing bolts to see what happens!!

Has anyone used a 12ton press to push out lug nut stud on brake drum? I have 2 on my 68 300 that you turn with your fingers. I have never done this before, would like to try and remove them before I have them welded in. Drums are in good shape, don’t really to wreck them. Any advise would be great!

I think this issue came up before on fuel gauges. My 68 300 had new tank, sending unit and updated voltage limiter. I unhooked sending unit and grounded it. Started car and fuel gauge went to full. Went and filled up tank and gauge only goes a little over half. I dont know if there was any...

Where is the best place to get lug nut studs for my 1968 chrysler 300. It has 4 wheel power drum , need to replace studs in front drums.

My 68 300 has 4 wheel power drum brakes and I have 2 lug studs that are not tight on right front, turning in hub. Ive never replaced studs before. Is this something done in my garage or does it need a press to remove and replace? Is this a simple repair or pain in the butt? HAPPY EASTER TO ALL!

Can someone tell me how to empty my inbox, Im lost.

Quick question, single wire alt on my 68 300. I did buy one of the solid state oem looking regulator from member. Voltage at battery at high RPM, but the gauge will peg and pulse from normal to mid at idle. Alt was rebuilt, new battery. Starts and runs ok, no over heating wires. I do have the...

Can some tell me what might be wrong with my head light motor, I have voltage to it but it wont open. With headlights on, I roll open manually and they open about half way then the motor starts to try and close back up. I can feel it kicking back the other way in my fingers. Any ideas what might...

Does anybody no where I can locate 2 rear side marker sockets for my 68 300. Ive been checking the usual places with no luck.

Im feeling kinda sick, 2 weeks ago I finally drove my 68 300 out of the garage and down the road and back with no issues. Felt good after 3 years! About 3 days later, before our roadtrip to new york, cranked it before we left and it ran kind of rough, slight clunking and oil light did not go...

Is there any tips on installing my new gas tank grommet in new tank? Ive heard heating it in hot water to soften up or vasoline. And then installing filler neck. Experiences on best method will be helpful! Thanks again guys.

Does anybody know where this wire connects to? On my 68 300, it was laying on floor board under driver side dash. I think it goes on steering column to ?. Can some send pic. Manual says should be grounded from column to not sure where, there is no photos. Im wondering if this missing ground may...

I just got my fuel tank delivered from summit. The original along with the bottom of my 300 were under coated. Should I apply any kind of sealer, protector or just leave bare metal? I have seen both ways. Any thoughts on this matter? I dont know if Texas heat will make any difference or not.

These are the wheels that came on my 68 300. All of the mounting holes on all 4 wheels look like this, my concern is are they wore out or do they have the wrong size lug nuts? They seem to go in to the wheel kind of deep. My other 300 had same wheels but were brand new as were lug nuts. The...

Hello all. Still getting my 68 300 ready for the road, brakes next. Can anyone recommend a good one man bleeder pump? Ive looked at a couple, real simple to bigger hand pump type. Any suggestions would be great!

One more question, going to change filter and fluid in my 68 300. Original, stock 727 transmission. Whats recommended fluid to put back in? Only a few options now days. Thanks for the help.

Does anybody have a picture of their carb set up on 68 440 or tips as to what goes where? Carter came with this 300, was in a box, junk. Put on this one, bought the linkage adpt but Im not sure where to hook things up. I dont remember how to set up the trans kick down lever. Also the pic of heat...