What are you working on today??

I'm back down in Tennessee for a few days on site with the contractors doing some inspections on the pole barn build.
It's expected to completed in about a week.
More pics of their progress tomorrow. Overall, the new shop looks great!

1.jpg


17.jpg


26.jpg


15.jpg


21.jpg


23.jpg


18.jpg


14.jpg


8.jpg
 
I'm back down in Tennessee for a few days on site with the contractors doing some inspections on the pole barn build.
It's expected to completed in about a week.
More pics of their progress tomorrow. Overall, the new shop looks great!

View attachment 746762

View attachment 746763

View attachment 746764

View attachment 746765

View attachment 746766

View attachment 746767

View attachment 746769

View attachment 746770

View attachment 746771
Looks great tim. where's the men's room, out by the tree line?
 
I needed to make a couple of T-harnesses for my Small Bobcat Articulated loader with snow blower This was my retirement gift to myself after working there 36 years and getting a nice Legacy Discount. I am a little biased on this machine as it was one of my Product Management projects doing a ground up design. I am actually listed on a Styling Patent for this machine.

Anyway I added rear defrost and am experimenting with a cheap controller for intermittent wipers. I don’t like cutting into wires, so I made some T-harnesses to plug directly into the circuits. Wire schematics are very useful. Also added some holders for my snow shovel and ice scraper.
IMG_9705.jpeg
IMG_0692.jpeg
IMG_0693.jpeg
IMG_0723.jpeg



IMG_0726.jpeg


IMG_0713.jpeg
 
Last edited:
While making my T- harnesses and collecting more different styles of connectors for my Bobcat SAL, motorcycle, Engine analyzer, and Polara, I decided it was time to organize my electrical drawer so I could find what I needed without dumping everything out. Found some nice organizers for $2-3 and put my label maker to use.

IMG_0711.jpeg
IMG_0712.jpeg
 
Old thread but always cool to see what's going on with everyone's projects. Winter here un Canada is very long. Good time to make changes hopping to go faster next season! Putting the Polara on a serious diet, porting heads, porting tunnel ram, getting the 2 x 750 double pumpers ready and matching the pistonsbto the bores. I had to order a kb162 as one of my pistons had a very loud knock/slap. Ended up talking it all out and thatbpiston was 5 thousands smaller than all the others. I bought just one new from summit. Hoping it will get here soon.
Merry Christmas everyone and show what you are working on!

IMG-20251207-WA0049.jpeg


IMG-20251207-WA0047.jpeg


IMG-20251206-WA0069.jpeg


IMG-20251206-WA0030.jpeg


IMG-20251206-WA0028.jpeg


IMG-20251209-WA0039.jpeg


IMG-20251211-WA0008.jpeg


IMG-20251211-WA0020.jpeg


IMG-20251212-WA0011.jpeg


IMG-20251212-WA0021.jpeg
 
Finally getting around to fixing the daily driver CRV. Amazon driver backed into it back in the summer. They are paying me very well for the repair!
20251217_091522.jpg
 
Looks great tim. where's the men's room, out by the tree line?
Mike,
haha... done that many times.
If you look close in the 4th picture you will see where I have the plumbed in pipes for a sink and turlet.
They've already got it framed in this morning using 2x6 studs.
With this years budget stretched out to the max with this project, the final plumbing, electric and driveway will be completed next year.

30.jpg
 
Last edited:
What's code on the tube vent? perhaps cheap out and install a window, in Wisconsin, they have to be wrapped with insulation LOL or really cheap, leave the door open and a can of freshener
 
I finally got the grease pit in the valley cleaned up and am preparing to install new intake plenums in the 7.3 Powerstroke.
I am also installing some fuel feed upgrades.

IMG_9375.jpeg
IMG_9376.jpeg
 
I am completely amazed how fast the construction went with building the pole barn.
The company crew that built it were always onsite when they said they'd be there and never had a problem if I wanted something changed or added during the build. Any minor concerns I saw that needed attention when on the property were handled quickly. (there weren't many)
The communication with them was always thorough and whenever a phone call was made, they always answered. This is a rare occurrence today. Most of the time I find myself leaving a voicemail message when contacting any business today.
If anyone in middle Tennessee is planning to build a pole barn or even a Barndominium, I would recommend checking out KD Construction.
The last thing that needs to be completed for this year is to have the overhead doors installed on the front & rear of the building.
Merry Christmas.

32.jpg


33.jpg


34.jpg


35.jpg


36.jpg
 
That is AWESOME. Where I am from start to finish was almost 2 years. The architect, building approvals, weather delays, you name it...slow and expensive and TOO many mistakes! This was "almost done". The ONLY good thing is this was pre-COVID. I could ONLY IMAGINE the delays that would have caused!


IMG_0485.jpg
 
You are blessed with your contractor. The building looks great!

We had to go through two contractors (one was Morton Buildings!) and finally struck gold for our remodel/addition with the third.

We received an email every two weeks with what happened, what is being worked and a two week look ahead.
The contractor was always quick to respond and made it right if something was not right.

Our contractor even paid for the duct cleaning because the sub that did the work left the floors a mess…

IMG_8575.jpeg
 
You are blessed with your contractor. The building looks great!
I did my homework before picking a contractor. A lot of companies wanted to sell a pole barn package.
Looked at Morton Buildings, Olympia General Steel and many others but found most the advertising we see for pole barns is for the material only. Most these places will put together a package for the style and structure, include hardware, siding, etc., and drop ship it to your property.
I found out after speaking with several companies, when the orders are shipped, you might not receive everything because of the tariffs. Some items could be on backorder.
In addition, if I would've taken that route, I'd need to find a contractor to build it, then a concrete company if the builder couldn't arrange it.
Finding all these separate companies might be an ideal way to go if you know who to use in the area, and if you're there to oversee everything. Essentially, you'd become the contractor and sub the job out to everyone else. This wouldn't have worked for me, being 9 hours away. When I found all this out, I decided to go a different route.
The company I used took care of everything. They had their own building crew, mostly Mennonites local to the area, and did all the ordering of materials. They also have a sister company that exclusively does their concrete work.
It just seemed the best way to go.
They broke ground on October 22nd. So, roughly 2 months from start to 99% finished today.
 
You are blessed with your contractor. The building looks great!

We had to go through two contractors (one was Morton Buildings!) and finally struck gold for our remodel/addition with the third.

We received an email every two weeks with what happened, what is being worked and a two week look ahead.
The contractor was always quick to respond and made it right if something was not right.

Our contractor even paid for the duct cleaning because the sub that did the work left the floors a mess…
I wasn't as "blessed" as you think. Too many mistakes, mainly the door openings. Were supposed to be 8' but he didn't take into consideration the brick veneer. The block is 8', but i lost a foot with the brick added. The garage is also at a slight angle towards the house. The smaller side is only 8' wide because the Buildings Department would not allow a 3 car, so the architect said it would be a "storage area". As it turns out, the angle and narrow width make it inaccessible with a car (at least what I like lol). Good thing though.....I need a work area and would have found a car for it if it were easy to access! I LOVE your set-up! I also have a 2-car built into the house. Only problem is one side is only 16", 11" deep due to s expanding the laundry room. Something I didn't think out when we built the house. At one time I had a 1966 Oldsmobile Cutlass. The car was 3/4" longer than the depth. I notched the sheetrock, but the floor sill was bumper height, so I only gained 5/8". I had to get the car perfectly straight and pull the door out to clear the bumper. The wind up is, that side collects junk.
 
Back
Top