Search results for query: window removal

Gentlemen, working on 68 300, electric window removal. Got the 3 holes precut, ignore the 4th extra hole! Passenger side, took out the 3 bolts, motor still now coming loose. I loosened the one at the bottom left,still wont move motor. Is there something still holding motor. I have the window...

stuck window woes Some pictures here. Front window, not sure how different from the rear this is. window replacement search #1 Then I would read just about everyone of these, skim read anyway. window replacement search #2 And more threads here that have some more info as well. Just...

Well it’s been about three years working on this 68’ 300 convertible and am ready to reinstall the vent window and window tracks and regulators. Removing those pieces was not in an “experienced manner” but rather a whatever and however mindset. Anyway here we are. I have reconditioned the...

The next project I have is the driver side power vent window. It works but needs a little persuasion to open and doesn’t close all the way by just a hair. Just enough to get the irritating whistling noise driving at highway speeds. I would like to take it out and inspect, clean, and re grease...

Hello and help !!! I have a 60 Plymouth Suburban and need to remove the interior door handles. Wow they are nasty things. What's the trick ? Window crank handles were relatively easy, door handles absolutely not. So frustrating, fought with it nearly an hour ! Thanks

I need to replace the motor on my passenger window. i see that the regulator is mounted with 3 rivets. when i go to reinstall, can these be replaced by nuts and bolts? i don't have access to a rivet tool that large. I haven't started yet, so any other advice? thanks in advance.

How do you remove drivers window on a 68 fury

Perhaps you could link me or tell me what heading to look for about the window removal and installation.

Hi all, I'm trying to strip my '68 Newport. How can I remove this c pillar trim piece? Is it clipped on or screwed from the inside? I can't seem to find it in the '68 manual... And does someone has tips to remove the rear window trim? I can't seem to unhook te clips. I did manage to...

Hi all, I’m down to the point that I need the windshield and rear window pulled from my 67 Monaco 500. I’ve been doing just about everything I can before doing this so clearly, I’m not keen on doing it myself. My glass is all in good condition and I’d like to keep it that way. So, does anyone...

Rear window removal on both my 66 and 65 parts cars showed a small amount of black sealer or butyl tape underneath the original molded rubber gasket.

Yes. Blue is the front, brown is the rear. I wondered about the clip removal as well. I had my glass guy confirm the hight with the trim before he put the glass in.

Look inside (3) of those pre-drilled holes, those will give you access to the motor and gear for removal.. Please be sure the window is in the up position and secured somehow so it doesn’t slide down once the motors pulled. Pictured is my 77 NYB drivers door.

I replaced mine a few years ago without any window removal,, only the interior trim....No problems 1966 NY 4dr HT

Time to take the door card/panel off. Use a metal trim removal tool since the fiberboard has a good chance of ripping out and the steel retaining clips can be stuck real tight; on every door panel of my car I tore out 1-3 clips pulling off by hand lol. Remove the moisture barrier, if it's...

sounds exciting ...oh boy.

Had the same issue with my 69 wagon that had been sitting for 30 + years. If you have a harbor freight store, go and purchase their blue colored plastic trim removal kit/...

appreciate the advice..doesnt sound like fun...lol

One can use Velcro or magnets to reattach the door panels if those clips pull out too much. I recommend FINGERS for pulling those old vinyl coated masonite cards loose from the doors, as much as possible, or a broad but thin pry-bar. The more surface area one can apply force over, the less...

I removed the wing vent motor and the entire side window bracket. It's a 1967 Crown HT. The shaft that connects the pivot to the motor needs to be removed in order to remove the glass from the triangle frame, which needs to be removed in order to replace the rubber and rechrome the frame. I...