Search results for query: *

I helped design the MT and now Icon pistons the are the only way to go mock it up to get tight quench like .030 035 with your milling, decking and gasket selection measure twice cut once 6 pack pistons with a wedge 915 head will most likely give you too much compression unless you D Dish...

Youfoud a return line on the muscle cars from near thefuel pump to prevent vapor lock I got 3/8 lines from a b Bpdy and used the stock 5/16 line forthe return stock had a canister but use the fuel filter mentioned above

I vote for SW springs you can take them apart and buil yoUR OWN pack clean and spraywith dry mol lube and use plastic full length inner liners makes them slide not stick I;d use a Cordoba s rear sway after putting LATE C body torsion brs up front and that front sway before the ear sway we...

find some donor station wagon sprigs extra spring rate helps you can rebuild yourself put in plastic interliners they work real smooth you can also put in front torsion bars from a late 70s donor expecially a wagon PC ot trailer tow then when you have the larger front bars put in a rear sway...

Ford supplement works best for me narrower drum to drum makes wider wheels easier u joint yokes vary somehow I think very tall ratios may take a different pumpkin (the pinion offset is different) but I may be wrong so check may be a brand x see the link above and study

stock rockers or 1.6 3/8 pushrods what carb ? TQ? HPmanifolds or? any quench how much

I had both 65 and 66 Imperials tw0 73 New Yorkers, 69 Polara 2 door 59 Imperial etc one thing not mentioned is that the converter and input shaft may be different and may have been changed if you rebuild the 65 small input tran go to the later trans and converter pistons are much harder to...

Absolutely TQ finding the right number is not hard

start with what monc440 said above cc your heads choices 440 6 pack pistons at 0 deck with a "D" dish milled to get the cr you want maybe a 100 cc dish KB quench dome pistons with the dome removed with dish you want for your fuel too bad no e-85 with a 9:1 motor Iwould run Howards 256 @.006...

find some sw leafs getsomelate 70's torsion bars from a sw orcopcar get a cordoba rear sway only after the heavy front torsions wider wheels for radial tires handle like a sportscar

well knon that the specs in the book are .001off for the #3 i had atoolfor that but you can make a reamer out of a straight old cam just kut some groves in #3 square put in while rotating and it will clearance #3 you can then use dykem and a bearing scraper me x factory zone rep

I always carried a station wagon jack, they are taller

transgo reprogramming kit, level 2 (tow) for heavy car you will also get their tech line good ideas above, start by adjusting kickdown, use atf plus 4 (change it TWICE unless your converter has a drain) adjust bands while pan off

use the larger late model torsion bars, especially with radial tires, wider 15 inch wheels, make it handel you can use a cordoba rear sway AFTER you source the bigger t bars

you can swap your later valve body after you clean it an I recommend a transgo shift kit, an keep your part throttle kick down, well worth it to use the later valve body

no time to read all the posts now but I'd have someone follow me and do the on and off the gas test looking for smoke that would most likley be rings then change the valve stem seals they have to be toast you can get a tool to do it in the car while you have your springs off check each...

There is a reason Mopar went to 3/8 and sometimes 1/2 inch o diesels ou need good flow no sharp bends and for those with OD trans go 1/2 put larger threads in trans case and larger fittings when you have it apart really helps those trust washers I converterd to straight cut gears best...

727 is more durable why they used it behind 6 cylinder taxis small block 727 cases are easy to find and you can swap your guts or find a 518 from a 92-94 truck' all good choices depending on use

flat black bbq black not enamel