Search results for query: wiring harness

...diagrams that may help, but the FSM diagrams always trump them. I suggest printing the diagram out, then take a highlighter to the wire or circuit. You should be able to buy a replacement harness. Evans Wiring Harnesses - Mopar Only That may save a lot of time and money in the long run.

Original Wiring Harness - Ignition Lamp Mounts on steering column and is part of the time delay lamp option Part Number: 3488479 Used on all A-B-C-E bodies 1971-75 model years There are 2 harnesses available. Both are complete. One has a replacement non factory style connector end. $45.00 each...

Are the engine harness and the headlight harness two separate harness on a 68 Fury? Or are they all one harness? My Fury didn’t have any under hood harness when I bought it. So I’m trying to sort that out now. Thanks for any help.

Working on the dash wires. My brother owned the chrysler for many yrs. Apparently the fan switch failed during this time. So he spliced the wires and installed a separate switch. (Noticed that replacing the switch requires removing the instrument cluster.) I will restore this to origional...

Building a new wiring harness using bits from used harnesses and some NOS pieces. It has modifications including electronic ignition and changed alternator wiring but maintains a stock appearance.

Time to drag out the wiring harness board pic. I've repaired wiring harnesses by getting a piece of plywood and laying the old harness out. Then I outline it with marker and finishing nails. From there, once it's laid out, I start to remove the wrap carefully and then replace one wire at a...

...I rewired my engine harness and found the Oil Pressure Switch wire and the Cold Temp Switch wires had been crossed at the firewall wiring harness block. Only after replacing both sensors did this issue appear as it sparked when I connected the Oil Pressure wire to the new switch. I suspect...

Are the trim pieces in driver quality? None or very little pitting?

The “external shunt”? A section charge path wiring between two splices in the engine harness acts as the external shunt for the later externally shunted ammeters. It was not a serviceable part, having its own part number.

It's not uncommon for such broken wires to exist in old harnesses such as in our cars. Have you got your FSM wiring diagram? Trace the broken wires back to their previous junction points, based on their colors, wire gauge and relative position in the harness. Then you can pretty accurately...

Need a few parts for a 72 T&C. Got some parts from a 73 c body at Carlisle that were not the same, so need to be from a 72. 1. Engine Wiring harness for 440 2. Fan Shroud 3. Cruise control stalk on column 4. Any saddle interior parts- front door panels and rear storage/compartment area panels...

If I had that problem I’d attack it two ways. First I’d find a service manual for my car. It will have wiring diagrams that include wire colors and wire gauge sizes. Second, in those years Plymouth and Dodge were essentially the same vehicle. Under the skin they shared everything. So I’d scour...

I'm calling 'wiring' different from 'ignition'. For 'wiring', I'm going with a kwik wire kit since all bulbs and items are 6V. the wires are meh and the insulation is worse (being a 70 year old car). My goal its to get it running and wrench on more correct methods during the off season. (similar...

Thank you. I will start chasing wires and grounds this weekend.

When I've done those, I use a piece of plywood and some finishing nails. I've seen this in a few factories where they are assembling a wire harness.

I fitted my '71 Imperial with power door locks when it did not have that option. I did this with all stock parts and wiring. I did not add remote activation, though. I believe it could be possible to add some form of remote activation control to the power door switch harness in the driver's...

Late to this party but as mentioned get a good used factory harness, go through it and repair as needed. This is where the FSM wiring diagrams come in handy From my experience, using a multi meter I test continuity on each and every circuit. If you have to open up the harness to do any repairs...

One way to run added loads with this system. Leaves the ammeter function intact and retains the factory dash harness and circuit protection.

The original Painless Wiring kits were for street rods. That is its heritage. Street rods that needed a full re-wiring, front to back. Their "ace in the hole" was the use of OEM-level Packard wiring wire and terminals. The two guys that started the company did that work in their garage for...

One nagging thought I have about this whole thing is, we NEVER know if a current or prior owner had even added something into the factory wiring or had made some "mods" to the factory wiring before their particular melt-down happened? I had previously heard of how "bad" the wiring was on the...