Search results for query: motor mount

...you already have taken the heads off, the oil pan will be child's play by comparison. Drop the center link and exhaust crossover if it's a single exhaust and if the pan still won't clear the Kframe, pull the motor mount bolts and either hoist it up a few inches or jack it from the bottom...

...seats, buddy seat, AM-FM-8 Track. Asking $18,000, Pawnee City, Nebraska, 68420. PM me for inquiries. It has been sitting for 10 or more years, hasn't run, needs a new top, and carpet. It looked to be a rust free car. He said it ran like a raped ape when parked because of a broken motor mount.

I ripped a brand new Schumacher motor mount doing burnouts in my 70 Polara convertible.

At the time of posting - Starting bid:US $3,800 - Time left:5d 15h | Wednesday, 11:33AM 1957 Chrysler Windsor Coupe - eBay Auction - Mount Jackson, Virginia eBay Description VIN : W5742746 For auction is a 1957 Chrysler Windsor Coupe.  It has a clean Virginia title in my name.  It has...

Yes, that is indeed what they do, even from the factory on day one. I have a 70 Hurst with the HP manifolds on the 440 TNT motor. Not only will the valve cover paint turn a burnt orange over time, if you use cork valve cover gaskets they'll dry out and start to leak, too. Tons of heat...

2120238 right side floating power motor mount. Never installed. Rubber is in good shape with no cracking. $60. Located near 18974. Thanks

I think the head of your bolt might stop your mount from settling low enough for the through bolt to frame to thread. Try it before you try lifting motor into car.

I guess I have a bad motor mount because I just destroyed fan blades and shroud leaving red light under power. Thems the ‘red-light blues’. Any suggestions on replacing said items? Thanks from Texas!

I checked the motor mount with the hood up. You can see the engine and air cleaner while in the driver's seat. Sure enough, even though this car has a throttle cable, and no linkage rods, I was able to replicate the WOT situation, while keeping foot firmly on the brakes. It looked like the...

thanks much to the both of you. i read and re-read and then look again at what i have going on. i was able to access the 3 motor mount screws. i clamped the window and propped it up from inside the door (just to cover my bases). below is what i found. going to clean it up and see what i'm...

Update: Replaced the motor mount, you called it Justin Plant! Figured that at $9.- at 'O Reilly's, I just get a new one. Also modified that new mount, thanks Trace 300 Hurst for that link on how to modify it. Works like a champ, no more problems. As far as the linkage is concerned, yes it is a...

I could be wrong. But I just don't think They make a Slant 6 motor mount for a C body. The demand is non existent.

...up) power driver seat,passenger reclining 440, new rings, bearings, lifters, oil pump, water pump, fuel pump, belts, hoses, urethane motor mounts, etc. Cylinder bores measured .0010" - .0018" wear so I decided to re-ring. Transmission rebuilt, convertor flushed, new urethane trans mount...

Back in the early 70's I had a built Ford Galaxie that ate up left front motor mounts. I went to the local HW store and bought a heavy duty turnbuckle with jam nuts and a short length of chain, connected it between the frame and engine, and never broke another mount. I could adjust it to allow a...

i had it apart of course someone was in there a million times im looking fo new hardware clips etc i also want to change the worn hinge pins i have them and the window plastic mount and while im at it im looking for rear power window motor fpr my 65 L vert both sides.

$10 plus shipping sound good?

Both mounts look good in the car. I will pull them out today and get a closer inspection.

318 ORIGINALLY NOW FIT A 340-360(WITH A SPACER,INCLUDED, CNC MACHINED) MOTOR MOUNT BRACKETS, BLASTED,POWDER COATED,GRADE 8 MOUNTING HARDWARE. WILL FIT; 1966-1973 C-BODY AND ANY 340-360 ENGINE DRIVERS SIDE HAS A CNC MACHINED SPACER TO MAKE UP THE GAP BETWEEN THE EAR OF THE ENGINE BLOCK AND THE...

Thank you so much I will be contacting them next week your the man!

It's a 318 poly "big block". Without being properly restrained, it can leap through the hood an wreak havok on the world. Haven't you ever seen King Kong?!?