Search results for query: hanger

On the 67 Fury, the front hanger bracket for the leaf springs - are the nuts meant to be torqued to 30 ft-lb? The FSM is a bit confusing on that. I tried to torque it up to 30 and snapped a stud... I just got a similar nut and bolt as a substitute but I got paranoid of snapping all four so I...

1969 Chrysler 300 taillight lens wanted. just need one lens. A good used one will do. It's for a wall hanger. Thanks. Will.

Enlarge and check out the hitch, tailpipe hanger and leaf spring for starters.

...it is probably a correct resonator for that car , it would be interesting to know when it was assembled on the car. The over axle located hanger is surely the one assembled on the factory. It needs new rubbers and will get them. Odd that the rubber straps have a white surface vulcaniced on...

Looking for one of each of these (see photos). 1. Dual exhaust LH side hanger bracket that mounts to the body. The hanger mounts to this. see photo below. 2. Wire clamp for hanger (need two - circled in photo). I already have the hangers. I was going to make them but would save me time if...

I'm urgently looking for the rear leaf spring hangers on my '69 Plymouth Fury. I need both sides. Unfortunately, I can't find any anywhere here in Germany or the US... There are some for other models, but they're attached with four screws. I need them with three screws. See pictures. Does anyone...

...directly behind the upper control arms, but there's a hollow box where the frame meets the firewall with some metal gussets on it. Also one at the front leaf spring hanger. The rear hanger has what looks like tow hooks as well. And according to the fender tag it has A pillar spotlight...

...a bad dual exhaust that droned, leaked, and rattled. I have purchased a reproduction of the original single exhaust and am missing the two hangers. Does anyone have a good set of original hangers? I can use a universal hanger at the rear if needed - I found one that almost looks original. The...

...anyone knows the roads in Mass, they really stink! We hit lots of horrible roads. One was so bad the left muffler decided to pull out of it's hanger... Jackie was driving and we hear the noise. She asks if I want her to stop but we were a couple blocks from the cruise night... we drove on and...

Used early 60s windshield washer bag with cap and hanger. Holds water with a couple of cracks on top. $10.00 plus shipping from 61109. No electronic payment. Check or money order.

You always find some great settings to take pictures of these beautiful cars at. The hanger in the background is cool.

Waldron y-pipe and midpipe, NOS muffler, tailpipe, muffler hanger, tailpipe hanger and tailpipe clamp.

An access hole!! A bent coat hanger or welding rod would probably do it. I think maybe a strong light with another set of eyes through the grille might help.... Perhaps even another piece of wire to pull it towards the latch. Then there's those cheap borescopes that work with your phone...

Bend the end of a coat hanger into a small loop that just fits around the hose and work it into the trunk, you may need to work in in from both sides. It is pinched between the layers. Alan

...95% of the piece, is the exhaust tips on a '70/71 Sport Fury GT. I think the only difference with the E- body tip and the C-body tip is the hanger and the inlet pipe. Possibly flipped over too. Although they never came on the 300Hurst, lot's of folks think they did because of a promo pic...

I could, but then thought about how hard it's going to be to fish a coat hanger through the new on as Alan suggested.

...engine forward a couple inches so the flex plate will clear the transmission bell housing. To support the transmission, you can use a close hanger dowel (about 1.5" in diameter) cut to fit between the inner fender wells and use bailing wire strung between the dowel and bolt holes in the...

I swung in briefly just to say hi, but as you said you were a one armed paper hanger so I left you swinging... without bothering you.:lol:

...seat, and the small crossmember that the leaf spring bolts to. It is a plate that covers the bottom of this area. The oval hole provides access to the nuts that hold the spring hanger to the frame. I couldn't find any picture online of the door wedges, so will get some from my car later.

I will run this by Accurate LTD as they are who we use on all of our exhaust tips.