Search results for query: hanger

...should all drain out and not get into the vents. When the drain gets clogged, water backs up until it can flow down into the vents. I used a hanger to "open up" the drain and then flushed it out really well with water. This was probably 5 plus years ago and I haven't had the issue reoccur...

...at, hence the question. OK, thanks for the photo, that helps a lot. I don't have anything on my shock mount crossover piece because my hanger is mounted to what is the backrest portion of the back seat. Does that mean that I can use the supplied mounting hardware TTI gives you without...

looks like a 500 mile exhaust. all the heat shields clean and present. like the exhaust hanger behind the muffler. beats the bejeezus out of how they hung the earlier cars by the over the axle pipe.

Center dump logs are light truck and RV applications. Based on the shorty 727 it prolly was in a truck. I had a 400 2bbl in a 77 club cab shortbox with same powertrain. Had a 2 piece driveshaft with hanger bearing.

The OEM tail pipe hanger for my 1965 Fury III broke. The U clamp around the pipe was suspended by some sort of thick rubber. I know the chance of getting a similar new hanger is zilch. I can drill out the rivet and just put another piece of rubber in, if I could find the material they used. I...

...you, I'd order the installation hardware from Accurate Exhaust. I assume I need the following, but please correct me if I'm wrong: -Tailpipe hanger, right side (ACC-753) - I remember that hanger to be a fully symmetrical piece but on the picture from Accurate the bracket appears to be...

I have seen where they weld a piece of welding rod (or coat hanger) on the door edge and grind it back.

...system, you'll see where the gunk piles up Right at the bottom of the rear cylinders. Pull the rear frost plugs out. Get in there with a coat hanger to break it up. Hit the front heater hose nipple with water pressure. When it's clear it's clean. Put in the frost plugs, or! , get those...

...more visible than O.E. because they do run with the frame rail and are larger in diameter than O.E. . Still a good system that deals with the gas tank offset to one side. Underneath, everything fits very nicely. Notice the original hanger for the right single exhaust is inide the right frame rail

Couple Flowmaster clones, mild steel because cheap. Spent an age being everything to line up, welded fully and added some hangers to get it to sit right. Needs another hanger up front really, I think I'll add one. Stuffed the rest of the pipe together with the passenger side just resting on...

Thanks for the link Tim. Universal hangers don't fit well w/ our 69-73 Chrysler models. The exhaust from Waldrons fits pretty well. Universal hangers were found everywhere w/ this hacked exhaust system I removed. There are some very tight clearances over the rear axle and rear bumper. Just...

Hi, looking for the left side bracket that bolts to the rear cross member that the large tail pipe's exhaust hanger itself bots to. This bracket is only on the left side. thanks going to a dual exhuast system. Rusty but usable is fine. thanks Martin Kane

I have an NOS hanger..upon closer inspection itis a piece if a tire sidewall!! I kid you not! So grab a scrap tire and start cutting! Lol!!

here's the issue i had with mine...the drivers side hanger plate is nicely cut to the shape of the shock crossmember...and then they welded the round hanger rod straight across it...if you try to install it like this it sits too high and the rubber hangers wind up jammed into the floor of the...

...is useless. Once the pin is in pry the ends up and take the retractor off the belt. Put it on the new belt and clamp the ends against the belt. To get the belt back in the shroud just put a hook in a wire coat hanger. Push it through from the bottom, hook it on the bolt hole and pull it through.

This hanger mounts to the upper rear wheelhouse which I believe would be the one you are looking for. It is only available new from Accurate Exhaust systems as far as I could determine............................. here is the link to that part: C Body Hangers, muffler and tail pipe ...

New hanger parts are here tomorrow, I will be ordering two muffler clamps from Accurate Exhaust once I measure the muffler inlet/outlet.

...and 68-69 l/s is 2863409...it doesnt list a 67 l/s HP casting #....i have a TTI system with HP manifolds...had to modify the rr TTI exhaust hanger to clear the lip on the shock crossmember and re-route the trans cooling lines from Vans but that was it...if the car has an older aftermarket...

...there and did not require the special bracket. You can see the tabs on their pic. If you have no tabs you drill 2 holes for each of the rear hanger brackets. They fit nicely into the shock mount crossover. I may be able to share pics later today if you need them. If you have the Tab style...

Well, I removed the valve covers and used a coat hanger to check the oil return passages...but they were all clear. I cleaned up the valve covers and put some new gaskets up. I did notice that the passenger side valve cover (where I see the most blow by) was "bent" open and not level causing...