Search results for query: hanger

I’ll throw my 2 cents in - I manufacture the tip hanger for ‘70-71 dual exhaust cars. The GT tip has a finger that goes into the rubber isolator. A non-tip car would use a clamp that had a finger that would be sandwiched between the clamp and over-axle pipe.

I am looking for 1 Hemi Valve Cover does not need to be pristine just going to use it for a wall hanger in gameroom.Let me know what you got. Thanks Mark

I didn't see any straps on rockauto, just the silly universal pipe hangers and eye bolts they sell. Anyway, I did some research and it looks like Chrysler redesigned their fuel tank straps in 1977, they went to the strap like I have that has a more aggressive "T" slot on the rear and the front...

eeyup. i'm replacing all rubber suspension bits minus the big bump stops on the stub frame because those were the only ones that were in good nick. I did see that. I've decided it's not worth the effort to try to push the bracket and bushing off the bar, I do want to make it easier to service...

...crank handle 2520395 (1) used LH mirror bezel 2931245 (2) NOS vent window swivel mounts 2663731 (1) used vent window pivot mount (1) used coat hanger w/ screws (1) used antenna bezel (1) used dash bezel There is minor blistering/pitting on a couple of the door handles most if not all the...

Tail pipe hanger for various c body,like new,mopar original part,$40.u.s. Shipping include

...ground, but cocked sideways. The resonator is fulled butted to the over the axle pipe and it sits too far back to line up with the stock hanger and camp. The resonator is also not even aligned to the car correctly. It swings outboard at the end of the car and lines up with the frame...

...spring bracket and other grommet? (top 2 items in 1st picture) - SOLD Coil bracket - SOLD Big block starter shim - SOLD Big block intake valley heat shield - $5 Lot of heater hoses -$5 Lot of misc hardware - SOLD Spark plug wire looms - SOLD Exhaust hanger - SOLD prices do not include shipping.

Ben, have you looked up the factory part numbers or any Moog part numbers for the swaybar links? Having that information would be helpful and would allow me to check my parts inventory.

Excellent info. Thanks, Steve!!!

Sorry, couldn't get to this until today. The width of the "hanger" at what I think is the important part of this discussion is ~3 3/8". The tape measure picture doesn't really show the measurement accurately, but it is 3 3/8". One side of the tube sticks out ~5/8" and the other side ~1/8"...

I drive past this place all the time and finally pulled in for a photo op. It used to be a hanger at an airstrip used by crop dusters here in the Phoenix area. As you can see in the background a housing subdivision has taken over the site as has happened to a lot of the farmland in the area. I...

...that in the formal years Chrysler introduced larger sway bars for 440 motors. I'm wondering if anyone with a fuselage Mopar that has links for hangers, rather than being bushed directly below the frame like the formal C – body cars, has ever run into a 15/16 inch diameter sway bar and what...

...forward part of the wheel well for fitment, consider moving the rear end back 1/2" to 1" instead. The way I did mine (in a Dart), was I drilled another locating hole in the spring perch. You can also put a spacer in front of the forward spring hanger, but that changes the angle of your shackles.

I can see why you won. Beautiful. The two hanger-ons like standing by your Imperial to let people think it is there Imperial. What a great looking car.

Update: test fit the TTI tailpipes and am on the fence about it, think they're down too low. The tips are an easy 3" from the bottom of the bumper, and I don't see a way to fix it due to how the exhaust hangers are set up, the hanger assembly takes at least 2" of clearance away.

Look at the frame by the front spring hanger. Place your floor jack under that and lift the body, one side at a time. I often put a hockey puck or piece of wood on the floor jack saddle to spread the force a bit. Another option is you lift at the pumpkin as far as you can and place a jack stand...

My buddy has started making these for Milwaukee tools to be hung on the wall, yeah relax it's on a derby website but regardless it's cool and has the imperial bird.laser cut into it. he ships all over Www.nlrderbyparts.com

At least on a fuselage body, a poor design in my opinion. However if this gets clogged the water will flow horizontally and drain out the sides and exit via the lower cowl drains, located behind the kick panels/rear of fenders. Not sure what year car the OP has or how the other eras are...

Chrysler original Splash Guards from the 1980, Part #418602? One set (1) pair, white with FURY in gold. N.O.S.in excellent condition with information and screws. Nice wall hanger. $65.usd +shipping