Search results for query: HOSE!

What size heater hose is required for a 1962 and 1967 Imperial, 5/8 or 1/2? Thanks!

While installing my shiny new washer bottle in my '70 300, I had to run a new hose as mine was dried up and disconnected. The tee for the washer hose is there on the underside of the hood, but the strap that supports the hose, so (I assume) the hose doesn't tug too hard on the tee and break...

OK here is the story. In looking for hoses for the 65 413 I see that it is hard to fine a lower hose with the spring in it. I see that the cure is a 13" X 1 5/8" spring that Ford web sites sell. Is this a legitimate fix? Other options? Thanks for the info you have.....

The fresh air intake hose on the 68 Fury (non AC) is boogered. It’s the hose that attaches to the heater box and the passenger side area near the kick panel (odd shaped oval). Does anyone know what the part number is? And where it might be available?

Used power steering hose. $20.00 plus shipping from 61109. No electronic payment. Check or money order.

when I replaced the timing chain I put a new heater hose nipple in the water pump housing. Now it leaks. What's the best way to seal the leaky nipple ; pipe dope on the threads, thread tape, or silicone or RV sealant? Paul

That hose may have been just stuck on there by some half assed mechanic in the car's past. It finally came loose. What you NEED to do is look through your FSM at the emissions section for some of the vacuum hose routing. Then the HVAC section for other hose routings. Maybe the fuel section...

My 64 Newport gets very hot inside even in mild weather, with the heater on ‘air’ (vent) button setting, temp lever on cold. Details: White exterior. Windows open. Non air conditioned Warm air comes through floor vent. Engine is not running hot. Will it hurt anything to install a summer shut...

How about the larger barb on the vacuum Tree that has a cap on it? Swap that hose onto that barb and find a small plug for that smaller barb. That loose vacuum hose has to be for something. Either the heater controls or maybe light switch if you have vacuum headlight doors or a vacuum gauge...

You what SIX? You may be right after all. That small nozzle had about an inch of hose on the end of it and I initially thought nothing of it figuring it was just the remnant of a broken piece of hose. BUT after further inspection the one inch remnant (and I can supply a picture if anyone is...

Wire splicing and simplifying the vac hose harness?

Gates has barricade fuel hose and barricade fuel hose for EFI that takes 225 psi. Not necessary for a carbureted vehicle. The barricade is good for ethanol fuel. It is not thicker than the other fuel hose, rubber is a bit more dense less pliable. Works good. I doubt you need 225psi hose...

Can anyone tell me the size of the vacuum hose between the brake booster and the vacuum canister, as well as the hose between the manifold and the canister? This is on a 1958 Imperial. -Gregg B.

I like what I see here. Both of my Old Mopars will be well fitted with the Barricade stuff.

Here is the engine pic. Original hose clamp still there.

Used Vacuum hose cluster from 60s? temp control. 8 inches in length. $10.00 plus shipping from 61109. No electronic payment. Check or money order.

six; the hose and the nozzle on the tree are of 2 very different sizes. Paul

Still trying to get to the bottom of my hot interior problem. At breakfast today with a sharp 92/year old retired Mopar mechanic, he did say there should already be a water control valve in the heater box. I read the repair manual today, there is one at the water inlet, cable activated. I...

first sentence should have read "you know what Six? " Paul

Does anyone know the pressure of the fluid in a transmission line cooler hose under operating conditions (in psi)? Reason is I'm trying to patch a transmission line in my 1975 New Yorker with 727 transmission. I'm debating on whether to use a cooler hose with 2 clamps on each end or a steel...