Search results for query: *

Hello! I've owned my '65 Fury for about 8 years, but have not driven it much, mainly due to a long standing electrical issue. Background: Factory 4 speed car, originally a 383, now has a nicely built '70 440. Rust free Arizona body, rock solid floor, frame, etc, stock suspension, steering...

Snotty - Thanks. I'm going to use the white gaskets between the backing plate and the axle housing, because that's what was there, but I'm not sure what I should use between the retaining ring and the backing plate. Metal shim (black in the picture) that was on the pass side backing plate...

Hello! I pulled the center section out of the rear end of my '65 Fury to replace it with a Sure Grip. To get the axles out, I pulled the backing plates from the axle housing. The axles are held in by a retaining ring on the brake side of the backing plate. In between the axle housing and the...

Mike - Thanks for the tip, but I already got the clips. Chris

SOLD!!!!! Not sure how to send payment through Facebook. Email me at [email protected]

Pic attached. These are the clips for the bottom windshield molding that mounts on the cowl cover. Au-Ve-Co does NOT have them, nor was I able to find any on Ebay. Au-Ve-Co has similar clips, but they will NOT work. The square portion of the clip is flatened so that it can fit into the...

Ok, then I guess a 741 will do me as well. I just missed one on Craig's list. So, if anyone has a 741/742/489 sure grip center section, please msg me.

Sorry for the wrong term. I'm aware they were called "Sure Grip", using "posi" is just a habit. So yes, I'm looking for a "Sure Grip" center section, or third member. 489 cases were the strongest of the 3 types, so I'd like one if I can get it. My engine is 500+ hp. I'd consider a 742...

Need a posi center section for my '65 Fury. Looking for one that's ready to go, bolt in and drive. The car has a nicely built 440 and a 4spd, so I prefer a 489 case. Let me know what you have. Thanks... Chris Monroe, CT

Thanks to all for their input!!!! At least I know that this is an original 4spd car, though it's odd that it came with a 2bbl engine. The car came with what I believe is the original engine, a REALLY tired 383. I was going to have it built, but I found a complete, running, recently rebuilt...

Hello - My Fury came with the broadcast sheet when I bought it. I've checked out the online decoders, but not many of the codes seem to match up, and I'm trying to figure out exactly what the car came with. Under axle it lists 293 - can I assume that that's the ratio? There's no 293 in any...

Hello! My '65 Fury has a very nicely built 440 and a factory 4 spd. I'm at the point where I'm going to have to buy a new right rear tire because if I stomp on it up to about 30mph, the rear tire will break loose and continue to spin until I take my foot out of it. So...I'd really like to...

Barge - Thanks for the info. I'll give Au-Vee-Co a call and I'm sure that they can point me to someone who carries the clip, since they don't sell direct. I do recall that there were some form of clips in the windshield channel, so I will see if I can figure out how the moldings go in. They...

Hello! Finally found a nice cowl cover for my '65 Fury, painted it, and it's ready for install. The panel was missing when I got the car, although the windshield trim was in the trunk. The bottom trim strip, the one that mounts to the cowl cover, only had 2 clips. They slide into the...

Thanks for all the replies! I SHOULD have mentioned that that the car is a '65 Fury III, sorry about that. Is there a link to the "Standard Parts" section of a Chrysler parts book as mentioned above? Chris

Hello! Can anyone post a pic for me of the correct type screws to use on the cowl panel? Thanks... Chris

Looks good. I'll send you a msg and hopefully we can work out the details.

Jason - Email sent. Thanks... Chris

Clay - Same request - can you send me a pic? Apparently, there were 2 different cowl panels, a flat one, and one with a raised section in the center. Other than that, the feedback is that all C body cowl panels are the same.

Can you send me a pic?