Wollfen
Old Man with a Hat
Hey guys i know i have read about using a vinegar solution as a derusting liquid and that most people have great success using 10 percent solution, i am assuming that you are adding ten percent vinegar to water and mixing?
Using vinegar as a derusting agent
- Thread starter Wollfen
- Start date
saylor
Senior Member
oxalic acid crystals, or behr #63 (i think) deck wash.
I never used it, but from what I've read, most use undiluted 5% white vinegar.
A lot about rust removal is written here: http://www.jalopyjournal.com/forum/forumdisplay.php?f=5
Search for vinegar and you'll come up with a lot of stories and answers. Look also at molasses while you're there. A lot of guys seem to like that too. I've used oxalic acid myself with great results.
A lot about rust removal is written here: http://www.jalopyjournal.com/forum/forumdisplay.php?f=5
Search for vinegar and you'll come up with a lot of stories and answers. Look also at molasses while you're there. A lot of guys seem to like that too. I've used oxalic acid myself with great results.
I just tested this on the inside of one of my ashtrays (don't think this is chromed). Standard 5% White Vinegar. I had to let it sit for 2 days and then wiped away all of the rust, fairly easily. The rust was gone but it looked like the metal itself was spotty, some spots darker than others. I do not know if this was from the vinegar or from the rust being heavier in some spots.
I also purchased Behr #63 which I plan to try next (thanks to Saylor for confirming I got the right stuff!)
From the MSDS "Contains oxalic acid solution (less than 10%)"
My understanding is the Oxalic Acid solution should be about 3% so I was going to dilute it down with water a bit. Based on my readings I am also expecting this to work MUCH faster, possibly in 30-60 minutes, depending on the strength of the solution.
I also purchased Behr #63 which I plan to try next (thanks to Saylor for confirming I got the right stuff!)
From the MSDS "Contains oxalic acid solution (less than 10%)"
My understanding is the Oxalic Acid solution should be about 3% so I was going to dilute it down with water a bit. Based on my readings I am also expecting this to work MUCH faster, possibly in 30-60 minutes, depending on the strength of the solution.
Wollfen
Old Man with a Hat
Mm, interesting, I may go buy five gallons of 5% vinegar solution and give that a go, i am curious to see what it does.
I have seen it work wonders it just takes several days to work, compared to the deck stain which works in minutes/hours; or so I am told. Let us know how you make out either way!
saylor
Senior Member
a critical thing to mention.
after treating, oil it or paint it or prep it immediately.
or it will rust. fastly.
after treating, oil it or paint it or prep it immediately.
or it will rust. fastly.
commando1
Old Man with a Hat
After a ton of Googling on citric acid rust removal, I have had excellent results by citric acid powder (ebay, health food stores, etc - very cheap) and ammonia.
bajajoaquin
Senior Member
The regular vinegar you get in stores (5%) will work fine, it will just take longer. You can also use the other acids mentioned. The advantage of the lower concentrations is that it will be gentler on parts that may have become a bit delicate with corrosion.
Stronger solutions should also be handled with care. Disposal should be done in a safer manner (spashing can burn or cause discomfort). Depending on the strength of the solution, bubbles may form, causing a bit of acidified mist in the area. It's not going to eat away your bench, or anything dramatic, but metal things in the area can start to rust.
Stronger solutions should also be handled with care. Disposal should be done in a safer manner (spashing can burn or cause discomfort). Depending on the strength of the solution, bubbles may form, causing a bit of acidified mist in the area. It's not going to eat away your bench, or anything dramatic, but metal things in the area can start to rust.
+1
70bigblockdodge
Old Man with a Hat
Anybody have a opinion, suggestion, smart a$$ comment on 5% vinegar on bronze valve guides, have a set of cylinder heads that got wet flash rust all over pita with wire brush/wheel?
I have not used Vinegar with bronze. It looks like a few options exist though.
http://www.wikihow.com/Clean-Bronze
http://www.howtocleanstuff.net/how-to-clean-bronze/
http://www.wikihow.com/Clean-Bronze
http://www.howtocleanstuff.net/how-to-clean-bronze/
70bigblockdodge
Old Man with a Hat
I want to clean the cast iron and not hurt the valve guides
Wollfen
Old Man with a Hat
Nitric acid will eat bronze for sure, but vinegar is an acetic acid, so not sure, worth a google check.
Stan.........comments?
polara71
Old Man with a Hat
Stan has been quiet this morning. LOL!
commando1
Old Man with a Hat
:mornincoffee:
68plymouth383
Senior Member
I watched a you-tube video that showed apple cider vinegar won hands down over regular. They soaked rusty pieces for the same amount of time, and the cider was the clear winner.
Similar threads
