Search results for query: Rag joint

So this rag coupler or joint is part of an additional shaft that would be located to the left of the "Coupling" shown here?

Before blaming the steering box, check every bushing, arm joints, ball joints, steering coupler, rag joint etc.etc...

Thanks for the response! Much appreciated.

Yes! Old tires willing,I will be at woodley.Just got done rebuilding the steering coupler and rag joint with great help from this site,(thanks to"73 coupe " for photos! Met my wife at Bob's Big boy car show,turned out we both had 65 Coronets in high school,she still has hers tho!

Trying to install the steering rag joint coupler but I don’t have enough clearance. When I bought the car it had a universal unit installed and bolted the wheel to the power steering directly but I want to finally get the steering wheel straight but I can’t get the new coupler to fit. I already...

Also found the rubber rag joint pretty bad....so will take the advise of others here, and try the Dorman 31002...may need 2, but they do not list the bolt spacing anywhere, including Summit. So ordered one, and if fits will get another. So far, so bad, but gettin it dun.

Beautiful car. May be Craig @mobileparts can help with coupler/rag joint. You can PM him. Want Ad in Want Ad forum is another idea. Good luck!

DRK SD front end work as of 6/2022 All New Inner & Outer Tie Rod Ends Upper & Lower Ball Joints Adjusting Sleeves Rag Joint Borgeson Steering Box Borgeson Power Steering Pump Pitman Arm Front & Rear Shocks New NEXEN Tires Front End Alignment And I still think not replacing the first link in the...

...control arm. I did a partial ball install w/ the old ball joint allow me to finish up brake rotor and caliper install. Below are side by side pics of the defective ball joint and its replacement. Here is back on four wheels again. Next up front sway bar bushings and intermediate shaft rag joint.

)i was wandering if anyone has changed THE LEFT (DRIVERS SIDE) MANIFOLD gasket with a 440 in it on a 72 nyb did u have to remove the rag joint (steering coupler )heat sheild. mine was all ready damaged * domeone put hollow nuts on a log manifold ? weallmost had to T&R The 440 . i...

On the noise, it may not be noticeable with the rag joint columns. Also a good alignment will help with the constant centering of steering wheel. Try to get as much positive caster you can.

That is not an original. The OEM are similar in look to a hockey puck, but are no longer produced. Here is some reading for you... Steering coupler needed Steering coupler found Rag Joint

OK, this is a RAG JOINT COUPLER. You need one of these to replace that with one from a Range Rover! DON'T SCREW UP THAT METAL!! I'm gonna find you the link to order one. If for some odd reason its not available, I've got two, one still unused. HERE! Buy THIS: You probably will want to...

To finish off the suspension rebuild was replacement of the rag joint. The screws were seized so steering column removal was the only option. With the column out servicing was pretty easy as the following photos show.

Got a good used rag joint coming in from Murray Park, and also have a destroyed one coming in to fool around with. Maybe i can figure out what works and doesn't work to repair these things after good used ones are gone. Stay tuned for updates and thanks for all suggestions.

Here is some info from rock auto on the rag joint Alternate/OEM Part Number(s): 3575303. Lares offers technical support for all of their products. Misdiagnosis is common on steering components and the technicians can help you determine if your part is the problem. Phone: 1-800-555-0638

...OEM rebuilt instead of buying another as I did. Pretty hard to fit these bolts and stud in this situation. But, on the joints, my rubber rag joint was almost in half, and was part of my problem on steering. But, the new Lares is great, and if it lasts half as long, all good. No point in...

One of their steering boxes in on the list. I recently had to mess with the valve body on mine but otherwise haven't torn into it. My rag joint is a little long in the tooth as well so it'll get replaced. All the other steering parts were replaced in 2016 and are luckily in good shape and tight...

Check the ground connection through the column. There is a wire or spring that goes through the rag joint (rubber biscuit) near the firewall. If it's on its way out, the horn won't work. Test the horn by running a jumper from the upper part of the column before the biscuit to the lower part...

...my steering column components before removal. So, fine, after cleaning the intermediate shaft, my marks kind of faded. So, I put the new rag joint in today, and guess what....my wheel is 180 off. This after new cotters and all. Great. Check your wheel alignment as you reassemble, before...