Search results for query: *

  • Users: M1911
  • Order by date
  1. M1911

    Steering Gear Removal.

    I got it out!!! Instead on prying at the knuckle I pushed up from the steering gear and it "collapsed" enough to get it off the studs. and bobs your uncle.
  2. M1911

    Steering Gear Removal.

    The roller pin is out of the knuckle, is it suppose to slide at that point? . I have the bolts out of the steering gear and tried to pry and got very little movement
  3. M1911

    Steering Gear Removal.

    Continuing my front end tear down. I am stuck on the steering gear. Any tips for removal? 68 Fury. Thanks in advance.
  4. M1911

    Torsion Bar Removal

    Is this the clip that I will break? C Body Torsion Bar Seal Clip
  5. M1911

    Torsion Bar Removal

    Awesome as always guys! Thanks again.
  6. M1911

    Torsion Bar Removal

    Thanks for the link I actually have access to a clamp on tool. . Yes it's the factory manual. After the bolt is backed out and without load is there still a crazy amount of tension? I get it will have the weight of the L-Control arm and Radius Arm. I know these can be complicated but the Service...
  7. M1911

    Torsion Bar Removal

    No I have the Uppers already out. The torsion bars run threw the Lowers. I do have a service manual but it is very vague on torsion removal.
  8. M1911

    Torsion Bar Removal

    I'm going to be replacing my Radius Arm Bushings and was hoping to do that without removing my torsion bars...can that be done? If not, having never done torsion bars, how big of job is it? I had "a local" tell me to take the bolt out of the bottom of the control arm and and unbolt the front of...
  9. M1911

    1967 Plymouth Fury III 318

    I know you need a shorter oil filter, but did you use a full size starter?
  10. M1911

    1967 Plymouth Fury III 318

    Did the Sanderson Shorties end up working?
  11. M1911

    Window Trim

    Finally had some time gave it a little extra pressure and got them off! Thanks Guys! Maybe someday I will be able to put the car back together...
  12. M1911

    Window Trim

    Thanks guys, I have a handful of trim tools I just didn't want to pry to hard. I will give it a little more pressure and hope it pops off.
  13. M1911

    Window Trim

    Nope, I didn't get that far yet. Do you need to squeeze the clip to release it, or will enough pressure do it?
  14. M1911

    Window Trim

    I got the screws out but when I pry it feels like I'm bending the trim too. I have the little pinching tool for trim should that be used, or is it just a little more pressure?
  15. M1911

    Window Trim

    Can someone give me a tip on how to remove this trim piece on a 68 Fury. I'm using my little kid gloves to try to get it off to not damage it but I just can't seem to figure that one out. Thanks.
  16. M1911

    Front Bumper Removal 68 Fury.

    GOT IT OFF!!! 3 more days of soaking and ALOT more "berries" and she popped right off.
  17. M1911

    Front Bumper Removal 68 Fury.

    I'll soak em for a few more days and see what happens.
  18. M1911

    Front Bumper Removal 68 Fury.

    I put a bar on them to hold them while turning the bolt, but I dont think I would have enough room to actually turn the nut.
  19. M1911

    Front Bumper Removal 68 Fury.

    I'm trying to take off my front bumper on the fury and with using a full can on penetrating oil, and giving in all the berries I have, I can seem to budge any of the 4 bolts? Am I going about this all wrong or am I missing something?
  20. M1911

    1967 Plymouth Fury III 318

    Crazy all of the Header manufactures not one C Body bolt up...
Back
Top