Search results for query: *

Hey Fury....installed the new VR today from you. Works like a champ!! Charging voltage at 1200RPM is right at 14.8ish. After an hour of driving, and heat...voltages stayed constant. No issues with loosing charging volts as VR heated up like the old VR did. Thanks again!!

Thanks Fury! Just bought one from your ebay store. I was cleaning up my wiring under the hood this weekend, and noticed my VR looks like some type of cheap plastic or something. I didn't install it, came with the car when I bought her last year. On a side note, my battery charges fine for the...

Thanks everyone for all the feedback! Glad to see that what I'm seeing is normal, and from extra research I did last night, I see there are some 'fixes' if I want. When I replaced the old battery, I did see that someone had installed a smaller battery. I had plenty of room , so went with a...

Digging deeper...found some good info on this, and the 'fixes'.

OK, it's late. Can get pics of gauges in morning if necessary. Will try to explain as best as possible. Stock '69 300 convertible for the most part. Installed new battery as was unsure of condition of the old battery. The following issues were seen before battery swap. But that's not why I...

Thanks David! Helps a lot!! I think I have most wires routed similar, except the one above the valve covers are too long. Will need to remedy this. Thanks again!!

found some stuff by searching 'wire routing', was searching 'sparkplug wire routing'. Would of thought 'wire routing' was too broad of a search. hmmmm

For my '69 300. I searched, and am still searching....but looking for some pics of proper routing of sparkplug wires. I believe I have all the proper brackets/posts and the wire holders, but not sure. My wires were installed by PO, and looks like he just ran them randomly. Please advise. Thanks!!

I was in the same spot. Needed to add tunes to my 69 'vert. Was going to put some underseat bluetooth speakers and use phone to control. Ended up using a Monster rockin' roller 4. Portable 100 watt self contained audio system controlled by my cell phone. Seriously rocks! Put in back seat. Get to...

I'm using electric gauges for water temp, and oil pressure. So just wires for me, except on vacuum gauge.

Thankfully Pep Boys is having a sale on chemicals! Gunk 2 for 7 bucks, also Brake Clean is 2 for 7 bucks! Stocked up!!! Used two cans of Gunk, can actually see the plug now, nice and clean at rear of block! Still could use more scrubbing, but hard to reach all areas. Always get nervous when...

Plug easily came out. One less thing to figure out! Senders be here tomorrow. Will start running lines/wires this week.

Found the plug. Soaking in WD40 before attempting to remove...

I don't have a plug/hole where that smaller brass fitting is to the right on the top next to the thermostat area. I saw that area in another thread somewhere. I'll double check in a bit. Watchin' NASCAR now lol.

Now I see! Thanks!! That's what mine looks like. I have that same bracket, plug is buried in there somewhere. I'll break out the flashlight in the morning and take a better look. Thanks again, pics speak a 1000 words!!

Standing by! Thanks!!

Re-reading posts here, now I see what you are saying. T might not be the way to go, since flow across sensor would be compromised. Hmmmm

I know, right! I thought they would of come with senders too. But nope. I think one was like 20 bucks, the other was 35, both from SW. Be here Monday.

MarPar...your pic shows where my OEM sender is now...right? Maybe I missed something. If you have more pics, that would be greatly apprecitated! ThankS!!

That's where I'm going to T off from. I still have my idiot light connected there, will make up a T fitting....hopefully! I don't see any other ports like shown in some of the pics above, but I do have a bunch of brackets in front of the pump, so cant really see front of pump.