Search results for query: *

Ok I purchased an 83 D350 crew cab with power windows and locks in the front and manual in the rear. Both power windows were inoperable at purchase as were the locks. I pulled the regulators and motors the drivers side motor was toast. I rebuilt both motors and replaced the drivers side...

There is no burning of wires or heat, here is what's happening. Pull out headlight switch, running lights, tail lights, and dash lights only come on momentarily before the stop ( groove to have just the running lights on). If I pull all the way to the stop the lights go off. If I pull the head...

So I recently sold my 1969 Chrysler 300 as I was looking for a different project. The new project is not a C body , but still a mopar. I have always enjoyed this website and forum as it's members always give good advice that is not just a bunch of BS and the content is helpful. So I figured I'd...

i was planning to do Mr.Cs puck rebuild of my power window motors on my convertibles rear quarter windows. I have the FSM but am I bit confused on how this process works for window motor and regulator removal. Yes I know the regulator may break my fingers after removing the motor. Or so I've...

Here is the ad 1968 Plymouth Fury Convertible 383HP 4 Speed

Here is my craigslist add 1969 Chrysler 300 Convertible Paul

440 big block just changing oil and noticed the oil smells strongly of gas. Car runs good when operating main issue is hot start problems. Car also had a lot of condensation /black soot that comes out of the tail pipes. I have not replaced the fuel pump since purchase 3 years ago. Does this...

noticed today I had a one drip per 3 minutes coolant leak on the rear of my 440 primarily on the passenger side. Oil is clean with no water in it. All heater hoses appear to be without leaks. Could this be a leaking freeze plug? Curious if any have experienced this. Thanks. Just wanted to...

I have a 69 727 w/out the partial throttle kick down (PTK) I have read some threads about the performance enhancement and the ease of this upgrade, but I have not found any step by step descriptions or pictures of this process. Also which is better and or easier to get the job done. The bolt...

anybody know where you can get replacement splash guards for engine bay on fusies? For clarification I'm talking about the cardboard prices that go between inner fender well and over upper control arm in engine compartment. Old ones are destroyed and look to be made of cardboard

1968 Chrysler Imperial Crown Convertible Nice car but seems a bit high. I don't know the market on imperials.

So I have had my 69 300 for 3 years and it has always been pretty sluggish off the line and stumbled during quick acceleration, but run great during cruising highway. I have adjusted timing and mixture screws recently. When I adjusted the mixture screws it seemed I had to back them out almost...

swapped a pair of 73 disc spindles onto my 69 300. New rotors new calipers new pads new proprtioning valve ( wilwood). I did not change out the master cylinder or brake booster as it already appeared to be a disc brake MC put in place by previous owner even though he was running power drum...

70 Plymouth Fury III 383 1Owner Awesome Project Dodge Chrysler Mopar...

i am starting this thread for encouragement as well as technical support as I have jumped head first into completely rebuilding the front suspension on my 1969 Chrysler 300 and at the same time upgrading the front drum brakes to 1973 spindles and discs. I would thank commando1 for his very...

My 69 Chrysler 300 with a 440 has started making some pretty obnoxious noise originating from the a/c. The car is a factory ac car that has not worked since my purchase of the car ( on my list of fixes but not at the top). Last week I went to turn on the heat ( which does work) and the whining...

So I have read about the headlight relay improvement and decided to buy the painless wiring #30815 headlight relay conversion harness kit after talking to them on the phone. It is SUPPOSED to be plug and play ....it is not. lets start with this I have a 1969 Chrysler 300. All headlights work...

I am currently in the process of putting a set of 73 spindles on my 69 300 to do the disc brake conversion. Last night I tore down the 73 spindles to clean and see what I am working with. It appears the bolts and castle nut that holds the lower ball joint to the spindle are pretty worn out...

My courtesy/ interior lights work great when opening the drivers side door, but they don't work when opening the passenger side. I took off the front kick panel on the passenger side and found the following wiring. I looked in the FSM, but it was not much help. I could not locate the male...

Was replacing the heater hoses on my 300 and dove into the project before realizing what a pain in the *** it is. Needless to say my hands are cramping still as I type this from using the pliers to get those damn metal clips off the hoses. Now on to the question, I realized that there was a...