Search results for query: *

Do the motors come out by removing two bolts or are they spring loaded and therefore, I would need to remove the entire regulator? Are the motors grounded by the body of the motor itself or through one of the wires? Is there a way to remove the switches without cutting the wires? I don't...

1966 Chrysler 300 440 Engine with A/C: Can one remove the valve cover from the right side without unhooking all of the A/C lines? Thanks!

1965 Imperial 413: Can one remove the right side valve cover without taking the heater box off from the fire wall?

1963 Imperial 413 engine with 25,546 original miles. I replaced the points, rotor, cap, condenser, plugs, ignition wires, installed a carburetor kit, installed a new intake manifold, new water pump and timed the engine. The Y pipe is on the exhaust but the muffler and tail pipe are gone and...

Is there a product that can be painted on joints welded together on exhaust systems to prevent them from rusting out? Mufflers and pipes last a long time but the welded joints seem to rust out fast. Thanks!

I am in need of a 1967 or 1968 Imperial Trunk Lid that is in good condition. Thanks!

383 Engine Air Cleaner Restoration: I plan to paint the outside gloss black. What are the recommendations for painting the inside of the air cleaner?

There is a gasket on the bottom of the air cleaner pan that fits in the small channel around the air cleaner that the top fits in to. My gasket is gone. What is the best material to use for a new gasket? Thanks!

My 1967 Chrysler seat belts are in poor condition. I think the webbing could be cleaned up but the chrome latches are very rusty. The webbing is a dark brown, which I don't see available. What is my best option? Who is the best vendor for seat belts. Thanks!

I cleaned and installed a new kit in the Carter AFB 4 barrel carburetor off of my 1963 Imperial 413 engine. I adjusted the float according to the specifications but I must have it too high, as it is overloading with fuel. What is the correct float level and drop level and what do others use as...

What is the best paint remover? Is Aircraft Paint Remover any good? Thanks!

What is the best chrome paint color available in an aerosol can that best resembles chrome for the dash and some engine brackets, etc? Thanks!

I need a double snorkel air cleaner with flat ends for my 1967 Dodge Charger that has a 4 barrel carb. Thanks!

Did another company purchase Herb's Parts? He had spray paint for Dodge, Plymouth and Chrysler interior colors available. Does anyone know who has those colors available? Thanks!

I cleaned the AFB carb and installed a new kit. Car starts fine, idles ok for a little while, but then it seems to "load up" and then will die, unless I increase the RPM. Do I have the float set too high? I followed the owner's manual as to the float measurement. Thanks!

The Amp gauge goes back and forth between C and D, sometimes pretty fast. Sometimes it is steady on idle but not always. Movement slows down if I turn on the lights. I installed a new alternator, tried two different used voltage regulators and the amp gauge has been calibrated. Any ideas...

Regarding a 1966 Chrysler 300 with original front power disc brakes, 440 engine. Is the push rod that goes into the master cylinder from the power brake booster canister, adjustable? I don't have any air in the brake system and the pedal is solid, but it goes down farther than I think it...

What is the correct radial tire size for a 1966 Chrysler 300? It had old H78-15 tires originally. I am thinking that would convert to P225/75R15. Thanks!

I am looking for a close up photo of the roof stripe end to end on a 1967 Dodge Charger. I have a drawing but I need to know the exact placement. Thanks!

1966 Chrysler 300 Wheel Cover Paint Color - What is the color around the "Disc Brake" wording and inside around the hub that sticks out? It looks like black on mine, but not sure of the sheen; gloss, flat or satin. Thanks!