Engine decode help

[Ironram]

Ok there is a local guy selling 5 440s and 1 that he thought was a 413 but casting number says can be a 413 or 426 and the stamping on the pad is all wackey.on the stamping too me i see T 41 then below that is a faint maltese cross and below that looks like either 126 or 1126 so i assume 413 TIA

 

[Ironram]

Faint maltese cross with hp sorry

 

[detmatt]

What's the casting date? I'm guessing the "3" is missing from the T 413.

 

[Ironram]

My thoughts also

 

[max426]

Can't read the pic you posted above, sorry if I'm repeating what's on there.
T = 1963 41 = 413 42 = 426
I can't quite read the date either, if 126 Jan. 26 1963, if 1126 Nov. 1962. whichever it is should still have a 1962 casting date or a very early 1963.
I didn't have my coffee yet.

Jim

 

[live4theking]

So what does the maltese cross mean? I've got a 413 in the shed with that marking.

 

[commando1]

 

[Ironram]

So what does the maltese cross mean? I've got a 413 in the shed with that marking.

http://www.moparts.org/Tech/Archive/motor/36.html

 

[livininharrow]

:yourock:

http://www.moparts.org/Tech/Archive/motor/36.html

i just printed off all of the info. awesome thanks. that confirms my numbers matching wagon.:sSig_thanks:

 

[1978 NYB]

So what does the maltese cross mean? I've got a 413 in the shed with that marking.

[FONT=verdana, arial, helvetica]Other Stampings [/FONT][FONT=verdana, arial, helvetica]Additional stampings may be found on the ID pad. They identify non standard engine components. [/FONT]​

[FONT=verdana, arial, helvetica]A - .020 oversize cylinder bores[/FONT]

[FONT=verdana, arial, helvetica]Diamond - oversize tappets[/FONT]

[FONT=verdana, arial, helvetica]E - Cast Crankshaft[/FONT]

[FONT=verdana, arial, helvetica]HP - High Performance[/FONT]

[FONT=verdana, arial, helvetica]L or LC - low compression[/FONT]

[FONT=verdana, arial, helvetica]M - .001 undersize main bearing journals[/FONT]

[FONT=verdana, arial, helvetica]Maltese Cross - .001" undersized bearing shells[/FONT]

[FONT=verdana, arial, helvetica]Maltese Cross and an X - .010" undersized crankshaft[/FONT]

[FONT=verdana, arial, helvetica]O.S. - .005 oversize valve stems[/FONT]

[FONT=verdana, arial, helvetica]P - premium fuel[/FONT]

[FONT=verdana, arial, helvetica]R - regular fuel[/FONT]

[FONT=verdana, arial, helvetica]RX or MX - all main or rod journals .010" undersized[/FONT]

[FONT=verdana, arial, helvetica]S - special engine[/FONT]

[FONT=verdana, arial, helvetica]WT or TW - water test[/FONT]

[FONT=verdana, arial, helvetica]X - .010" undersize crankshaft[/FONT]

 

[cantflip]

gee could you draw us a picture? wow!

 

[70bigblockdodge]

The diamond is the only one that screws you for oversize lifters then you have to bush the lifter bores. By the rust on that block undersize bearings are not a issue

 

[commando1]

I never even thought to measure tappet bores before this.
Then again I have never had a block stamped with a diamond...