Search results for query: *

I have a pair of Trico wiper arms for sale that were removed from a 1966 Polara. They'd probably fit other slabbies too. Spring tension is good. 20 bucks, includes freight in the continental US.

I'm looking for a used pair of manual seat adjusters for the driver's side bucket on a 66 Polara. Part #s should be 2583139 for the inner and 2583141 for the outer. I hadn't checked with what's his name out east yet. but I thought I'd throw it against the wall.

I used to have information on a company that rebuilt power seat assemblies for older cars. Unfortunately, I've lost it. Anyone? Thanks!

NIB outside cat whiskers. These go on the door/body side. NOT the inside! Fit 66-68 C body convertibles ONLY! No hardtops! Asking 90 bucks and that includes freight in the continental U.S. only Paypal: dsertdog56@hotmail.com

When I purchased my '66 Polara convertible, I procured a set of vintage aluminum slot wheels to install on it one day. That day will arrive shortly. However, before it does, I thought I'd check one last thing. Hindsight 20/20 and all that. I want to discuss load weights. The wheels for the...

My sweet little '66 Polara ragtop has what I consider a typical Mopar electrical system. When you turn on the lights, the temp gauge goes up (goes back down when you turn them off), and the fuel gauge goes up. My sense tells me this is a grounding issue but where would one start? I have an FSM...

I need to remove the passenger door glass on my 66 Polara convertible. The FSM states I have to remove the vent frame and door glass as a unit. I don't have enough hands. Is there any way to remove just the vent frame without the window glass? I need to replace the guide shoes and weatherstrip...

I have a set of non-bright wiper arms that came off a 1966 Polara. They're in very good condition, and the springs seem to be ok. I'm asking thirty dollars for the pair, and I Will include freight in the continental U.S from zip 74012 (Oklahoma). There is some tape residue on them that can be...

I have four left over NTC3486 steering joints. These are a Land Rover part which has to be slightly modified to fit. I'd like to get 20.00 a piece for them plus freight in the Continental U.S. These ship from (Oklahoma) 74012. Seems that 10.00 might be the going rate by envelope. If you'd like...

Our 66 Polara has the variable speed wipers on it. While we do our best never to drive in inclement weather, the wipers aren't very reliable, and I'd like to improve on that. The symptoms are: Turining the wipers on, the blades cycle a few times then slow down. Sometimes they stop, then...

In my 66 Polara 383, I recently did a timing chain replacement and installed a new water pump hosing which I cleaned thoroughly and replaced the temp sending unit with one from a1967 and up application, which the stud connector instead of the spade. This also eliminated the jumper wire from the...

After reading a couple of other threads on early power steering brackets, I realized my pump had been adjusted wrong. The bushing was missing, so I'm going to place an order for one. Now another question arises. Although everything appears to be aligned, the bracket that mounts the pump to the...

Will a B body 383 pan (Charger, Coronet) fit a '66 Polara with a 383? They look the same (no steering relief) laying under the car. Thanks in advance!

I have about 45 of these 21068 filters for sale. They are brand new and were made by Wix. They are not the gold filter but they are a quality piece. They fit Mopar engines from the late 70's to early 80's and also various Ford engines. I'm asking 2.00 each plus freight, plus freight, shipped...

For '66 Dodge Polara. Can be 2 or 4 door. This is the piece that the U-bolts go through and is the lower shock mounting point. The FSM lists it as a bracket. I need a pair please, Southern metal preferred. Thanks! Shipping would be to 74012

So today I changed the oil in the Polara. I must have done this a lot of times on big blocks back in the day. But this time was different. I drained the oil and removed the Wix filter I filled the crankcase with Lucas 10-40 and primed the filter with about a half quart of oil, then screwed it...

Yup ... I'm down to the last belt to complete my set in my 1966 Polara The belt I need is marked "Pointier 200-1" It has the lock clasp and is about 42.5 inches long from clasp to mounting hole. Other Pointier number will not match the clip in the retractor. It can be dark blue or even a green...

My grille is spot welded to the trim /frame piece. I have a piece of material I can cut to fit the opening, but has anyone done this and how did you remount it? Thanks.

I need a pair of reproduction or NOS front parking lamp gaskets for my 1966 Polara. Thanks!

In my 1966 Polara... does it have AGC or SFE size Fuses? Can't tell and the books aren't helpful. Thanks!