WANTED A/C line needed

[bluefury361]

I need the A/C line that connects the receiver dryer to the expansion valve on a 1969/70/71 C body with manual A/C. It's the last link to the Admirals A/C system.
I thought I was good until I noticed the "kink" in the line at the forward fitting. Mine might work but is very restricted.... need to replace.
Used on all 69/70/71's and perhaps later models as well.

Thanks, Will.

 

[Polara_500]

An option - a hose repair shop could likely redo that end for you.

 

[BIGBARNEYCARS]

Friend Will. If you can not find a place to copy that line you might try CTC AUTO RANCH in Denton, Tx. They show several dozen C-Bodys partz carz of those 3 yearz in their inventory and Those folkz in Tejas know all about A/C in their ridez from way back. 940-482-3007 G L with the chase , Jer

 

[70bigblockdodge]

Same as a Newport?

 

[MrMoparCHP]

I might have one.

I was able to do some bodywork on a hose with similar damage. I used a drift on the inside till I could get a #3 Philip screwdriver in, the drift hit the curve in the tube before it fit the diameter.


Alan

 

[1978 NYB]

Will, if you can't find one....these guys probably can make a new one for you.

They rebuilt my A/C lines for my NYB in less than 24 hours.

http://www.benzhydraulics.com/

 

[rexus31]

Try Classic Auto Air.

 

[bluefury361]

Same as a Newport?

Yes Dave..... A 69/70/71 Newport with manual factory air will be the same. Let me know if you'd like to sell it.
Will.

 

[polarus]

Hi Will, I'll check around and see if I can find something decent, stand by.

 

[70bigblockdodge]

I will look, I had one, I will see how rusty and send pic.

 

[polarus]

Sorry Will, no luck. If nobody has one I'll try a salvage yard out West, I need a few things myself.

 

[MrMoparCHP]

I will dig for the one I have as well, that way you have a choice if there is a difference.


Alan

 

[70bigblockdodge]

Will did you find this piece I have one, it is a little rusty but no pitting bend to bend is about 31" long, male end at drier female at TXV.

 

[MrMoparCHP]

Here is another if that will not work.

This is off a 69 Polara with a 383


Alan

 

[bluefury361]

Here is another if that will not work.
This is off a 69 Polara with a 383

You've been holding out on me Alan.... . That's the one I need. PM, (whoops, conversation me), with price payment preference.

Will.

 

[bluefury361]

Will did you find this piece I have one, it is a little rusty but no pitting bend to bend is about 31" long, male end at drier female at TXV.

Thanks Dave. I need female ends at both connections. Looks like Alan has it covered.

 

[70bigblockdodge]

Thanks Dave. I need female ends at both connections. Looks like Alan has it covered.

Okay mine is more 90/90 zig zag at the drier not like Alan's

 

[MrMoparCHP]

Okay mine is more 90/90 zig zag at the drier not like Alan's

The one on my CHP car (a 69 HP 440 Polara) was 90/90 also not like the 45/45 one I previously posted as available.

An original line that have been cleaned up, the one I have available should clean up this nice (vinegar and steel wool).

Alan

 

[bluefury361]

The one on my CHP car (a 69 HP 440 Polara) was 90/90 also not like the 45/45 one I previously posted as available.

An original line that have been cleaned up, the one I have available should clean up this nice (vinegar and steel wool).

I saw lines like this one on the 68's I found in a salvage yard. I need the first one you posted Alan.

 

[A38E86D32]

I need one of these for my 71' Fury if anyone has one available. ..
Thanks