Search results for query: *

  • Users: Waggy
  • Order by date
  1. Waggy

    1970 300 Power Seat Switch

    Well I got the unit apart and back in except for the middle section, which either was broken or I broke. I believe the switch is a NU523 Front Seat Control Switch. There were 3 sections, which each held a switch. The sections were like a ice cube shape with clips on them. The middle one fall...
  2. Waggy

    1970 300 Power Seat Switch

    I have found my power seat switch is draining my battery over a day or so. It seems like the middle switch is not going back to the "neutral position". I am in an area with a lot of new homes being built and I think the trucks going by, shakes the car and the power seat tries to move and then...
  3. Waggy

    1970 300 fuel gauge

    I got it working! Had to take the dash out. I compared it to the other used one I had, checked all the parts and took the best of both, cleaned them and put them back. It works! Thanks for the advice! It is great to have a place to go to "talk" with others about the problems you run into...
  4. Waggy

    1970 300 fuel gauge

    2 studs
  5. Waggy

    1970 300 fuel gauge

    There is a 5 volt Voltage limiter
  6. Waggy

    1970 300 fuel gauge

    I have replace all of the wiring on my 300 (thought it was a good idea at the time, but not sure now!) and still having problems with the fuel gauge reading. Before I tear it all apart I wanted to get an idea how it works or what to expect. Normally I expect a 12 v power going into the unit, a...
  7. Waggy

    For Sale 1969-1971 Chrysler New Yorkers (not mine)

    It would be a nice drive back in the summer. That open road and that power under the hood! I have taken my Land Yacht on many of those trips across the country and the only problem was they ended! There were times, I just wanted to keep driving, the road was straight, the sun was out and the...
  8. Waggy

    1970 300 - Replace Wiring

    The Painless harness (10127) I purchased was for 1966-76 Mopars, so it should have worked, I would think. The manual I am using is for a 300/Imperial and Painless said it worked for the Imperial but did not mention 300. I wish Painless had a diagram for their wiring harness. I will check the...
  9. Waggy

    1970 300 - Replace Wiring

    I thought purchasing a new modern Painless Mopar harness was going to be the answer to my electrical problems and maybe one day it will! I have found Painless of NO help and I use to think I understood car wiring. I thought I had all of the turning signals working, but then I ran into some...
  10. Waggy

    1970 Chrysler 300 - Wiring Replacement

    Well, the brake light switch I was looking at was the brake warning switch in the engine area and the switch is under the dash! The inside "dome" lights still have me confused. I think it is a yellow and pink wire that connects to the light socket. The bulb has 2 connectors or nibbles where I...
  11. Waggy

    1970 Chrysler 300 - Wiring Replacement

    Well, I am still working on the PainFULL wiring harness! I use to think I understood electrical diagrams! It could be age! I got lot/some of it done. The problem is figuring out what Painless harness does and what Chrysler does. 1) Painless expects 2 wires for the brakes and the 300 has...
  12. Waggy

    1970 300 Concealed Headlamps

    I went with a relay that powers on wire when the trigger is off and another wire when the trigger is on. It Works!!! The only thing I am wondering if my main power should be coming from a keyed power source or just a constant power source such as the battery?
  13. Waggy

    1970 300 Concealed Headlamps

    I have a 1970 Chrysler 300 with Concealed Headlamps and I would like to re-wire it, so I need to understand how they work. I have disconnected the motor leads and I thought when one lead had power, that it would cause the unit to open and if I connected the battery to the other motor lead the...
  14. Waggy

    1970 Chrysler 300 replacement harness

    Well, the unit is working! The switch had moved down on the column, so when I turned the key, the connecting rod did not push the switch enough and the switch did not engage.
  15. Waggy

    1970 Chrysler 300 replacement harness

    Well I tracked it back to the ignition switch! The problem is I have a tilt replacement steering column and there was some interesting wiring to connect the old steering column harness to the tilt one. The switch has 9 poles and I have checked all the poles in the 3 positions the key can be...
  16. Waggy

    New wiring harnesses - C bodies

    About a month ago I started installing the Painless one, DO NOT do it. I looked at replacement harnesses and worried that what I got would not fit my car. If I was going to do it again, I would get a spare harness, if I could find one or use the old one. I would lay the harness out on a table...
  17. Waggy

    1970 Chrysler 300 replacement harness

    I have had so many problems with my electrical, I decided to replace all of the wiring harness with Painless. What a mistake that has proven to be! Painless is NO help, so I am hoping I can get some from the forum. I thought I knew something about wiring as I did wire up a 36 Chev hot rod and...
  18. Waggy

    Power windows out of order...

    I just had that problem with my 1970 300. It seems to me there were breakers out there at Summit and some of the other parts places. Sorry, I did not need the parts, so I did not order it and I cannot remember what the solution was but I am thinking it might have been a fuse. I have been...
  19. Waggy

    1970 Chrysler 300 - Wiring

    I have removed all the old wiring and replaced it with a PainFull Wiring Harness. The harness is OK as far as it goes, but the section about Mopar is useless! There is nothing on the dash. I was hoping someone could tell me how to set up the charging gauge. They have nothing on warning light...
Back
Top