Search results for query: *

  • Users: MEV
  • Content: Threads
  • Order by date
  1. M

    Mopar engine adjacent.

    My shop looks like a chevrolet dealer from the 50's. Rest assured my new yorker is parked out front.
  2. M

    Does this Lift make my stroker look fat?

    I know this is the wrong forum, but since i only post in here, I think it is appropriate. Drove to texas on tuesday from WA state to pick up my new MADE IN AMERICA car lift. Hornswoggled a couple of buddies to tag-team drive the ~4000 miles there and back with me. As you may or may not know...
  3. M

    Off topic long-shot question

    Anyone one here been to south africa and/or namibia recently? I leave in a few weeks and the violence down there has me spooked. Lots of $$ tied up in the trip and the outfitter says it dosent warrant delaying for a year
  4. M

    HEI style distributor cap

    Does anyone make a high quality cap for out distributors that has GM HEI style terminals?
  5. M

    Elective surgery on 505 C.I. stroker

    Morel roller lifters out, Johnson lifters going in. I have had a few occasions where the Morels have failed to maintain pump-up, and suffered an outright failure in a big block chevy build using morel lifters. I decided to preemptively swap them out. After drawing a few pentagrams and...
  6. M

    66 new yorker 4 door rear window motor acting up

    I have a rear window motor that will not go up either with the master drivers door switch, or its own switch, I have the assembly out of the car and have verified the motor is good (it is a newer dorman motor) it will roll down, not up. The switch and its connector seem clean.
  7. M

    489 open headers video

    Not specifically mopar related, but its cold outside and the posts on here are a little slow lately. My new project build. Just fired up my black truck motor.
  8. M

    489 stroker AFR heads ready for first fire.

    My chevy twin to my 505/512. My mopar build was a blast so i decided to build a big block chevy for one of my trucks!
  9. M

    Tricks for tailshaft re-installation on a 727?

    I installed a A&A 6200 RPM governor in my 727 in the car and am having a bear of a time getting the parking rod back in correctly. Anyone have a trick for lining it up as you slide the tailshaft back on?
  10. M

    1966 newyorker 12.30@110 in-car video

    Driven to the track ~70 miles 3.23 gears with detroit locker 4767 lbs The popping and banging you hear is the ricer in the right lane.
  11. M

    Quickfuel carb tuning

    Any quickfuel carb Jetting guru's on here? I finally got around to installing an 02 sensor in my 505/512 stroker and got some readings at various loads. I am not a jetting expert and could use a second pair or 2 of eyes on my numbers and jetting choices.
  12. M

    275/50 15's

    Got the new Mickey Thompson ET street R tires 275/50 15's mounted. They fit under the fender skirts. Should get me to 11.99. If you look close in the pic you can see the old M&H drag radial 275/60's under it.
  13. M

    Plans for 11 second quarter mile this year. In car video link.

    This year I have made a few changes to hopefully get into the 11's First off i purchased and installed an innovative motorsports 02 sensor so i can actually tune the quickfuel SS830 carb I run. This carb has never been jetted or adjusted other than idle mixture and idle speed. It is exactly...
  14. M

    11 second quarter mile

    I swear, I will run 11.99 this spring"
  15. M

    150 shot nitrous

    Anyone running nitrous on their stroker? I think i am going to add a 150 shot to my 505/512 stroker. Can you run the nitrous outlet stinger wet plate on an unmodified performer RPM manifold? I am very hood clearance limited.
  16. M

    WANTED Need a 489 center section

    I need a 489 centersection for an 8 3/4. Preferably in washington, oregon, or idaho so i can pick it up. Gear ratio does not matter.
  17. M

    66 newyorker steering column/shifter stiff

    I recently removed and repaired my gas gauge in my 66 new yorker. The gauge cluster removal required loosening and dropping down the steering column, including loosening the bolts that go thru the firewall around the lower column support. When i re-installed the column the shifter was tight...
  18. M

    Took the 1966 Newyorker 4dr to the dragstrip today

    After my comp cams hydraulic lifter failure on the way to a car show last summer, I replaced my cam and lifters with a straub technologies custom grind cam and morrel lifters. (comp blew me off, so no more comp cams for me) went back to the track today and ran 12.35@108.45 60' 1.71 I still...
Back
Top