Search results for query: *

Can someone give me a heads up as to where I can get a decent sending unit and the tool to remove it for my 68 300. This my next issue, ive got to remove my tank and have it cleaned or replace it.

Does anyone know where I might can find these badges. On convertable they are on quarters, fast tops on pillar. I think they are the same?. Mine were missing when I got the car. Previous owner had removed vinyl top, these were missing. Having a hard time locating.

I have a problem!, after getting ac back on I noticed not lining back up, bolts. Power steering pump bracket not going back on right. Long story short, the pump housing I bought, right side bolt holes are longer than my old one. Have the same part #. Im thinking new one is non ac app? I dont...

Im in process of putting 440 back together, can someone tell me specifically which bolts go in the water jackets when reinstalling the waterpump housing or should I silicone all bolts going back to be on the safe side.

I just received new OEM pcv valve, can anyone tell me what the nut is for? There isnt one one the old one, I dont see the purpose.

Another quick question, fixen to reinstall my intake on the 440. Does the valley pan gasket need any silicone applied, where what type? The did not look like had any on it, I think I read around the ports? Both sides? I want to all this back together right the first time!

I have a quick question, is there an easy way to press balance back on? I tried a rubber mallet to tap it on. Only goes so far, I dont know if thats a good idea anyhow. I pulled back off, the fsm mentions a tool to press back on. I dont want to mess anything up doing it wrong. Any imput would be...

Ive been reading different scenerios for marks, before I cover this back up, I set balancer at tdc, rotor was at #1. This is where the marks were when I pulled the cover. Crank mark at 12oclk timing gear mark at 12oclk. I put new back on the same way, is this going to be an issue? This car was...

I got a new idler pulley, my question, can I reuse the notched bolt and bearing cover on my old on the new? Did I get wrong pulley assembly? Do I need to drill out these rivots, any thoughts, ideas. Heres pics. Old pulley, new one just has bolt hole, old bolt is notched to not spin in the bracket.

I got a new push rod for fuel pump, im not sure how to get the old one out. Its probably simple, im just not sure. My service manual says nothing about that. Help please.

Does anyone have a quick way to remove the crank oil seal from timing chain cover? I dont have or can find a special tool to remove it and put new one in and I dont want to damage cover! Any tips always helpful. My parts should be here tomorrow, want to get 440 back together this coming weekend!

Well Ive got front of engine tore down, it has been apart before, but looks to still have fiber gear. I guess Ill go ahead and pull intake in ck all that I can, dont really want to pull the heads. From what I can see inside, looks pretty clean. I now have my winter project!

I need some advise on whether or not to change my timing chain and gear on my 300. I have my water pump housing off and timing cover is wide open for removal. Ive never done a mopar change out. Would I be smart to go ahead and change out? Ive already got crank set on on dead center and dist...

I had to buy a new temp sensor for my water pump housing, and a heater hose nipple, should I apply any type if thread seal on either one.? I know the sensor is brass, it was difficult getting the old one out, didnt appear to have anything on the threads. I want to make sure and I get it right...

Can anyone recommend a good after market carpet manufacturer with good quality material for my 300? Ive been looking on internet, found 2-3, just dont know which one might be best for quality and cost.

When I pulled the water pump housing off the block the other day, there was quite a bit of silicone around the ports. When going back with the new, do I need silicone, if so what type or just gaskets. I did run a thin bead on the pump in the past but never had the housing off before.

I need to replace my water pump housing on my 300. Can you still get cast housings, all im seeing is aluminum. Any suggestions on alum vs cast? I pulled off my a/c compressor to get to t/ stat housing and found pump housing cracked.

Quick question, I pulled the electric seats out today and I noticed only one wire going to each one. Assuming that it would be power coming in, could I hook 12v to that switch and ground the frame and ck operation of motor on the work bench?

I just pulled the dry rotted carpet out of my 300, this is what I found. Looks relay good and solid, couple of minor suface areas, nothing to worry about. The underneath has been undercoated and it is still solid, just peeling off in a couple spots. No rust! Does look it was hit on pass side at...

Does anyone know if there is a way to manually open headlight doors on my 68 300?, i had a 69 about 10 years ago and I could with knob on bottom of motor. Cant seem to find away on my 68.