Search results for query: *

Hey all, I am trying to sort out some little things on my car before I can list it for sale :(. Cant enjoy it as much because of a back injury, it really really sucks. However, I am trying to figure something out with my cooling before. I have replaced my one 16" Spal with a decent shroud and...

Hello, I am running a 360 with and EFI system that runs timing control too. I have a spal 2000cfm fan and Never really had a temp issue. I added an AC last winter and today was my first real day using it in 95° weater. No temp creep or heating up while driving, stays close to 200° but when I...

I discovered this a few weeks back. Car runs fine, does not overheat at all. Fan cools it down quick from 210 to 200. I have replaced the cap thinking that could be the problem. Should I be concerned much or is it just poor china construction? Could be that I had filled the radiator too much?

I am playing around with the thought of wanting to put an AC in my car. My Plymouth was an original 318 with AC. Still has the hvac box but only for heat. The engine was switched to a 360 with no AC. Has anyone used a system from vintage air? I am a little overwhelmed by their selection... I...

Does anyone know of a good alternative to the standart cooling hoses, I am gonne replace them all after limping home just now. Any affordable silicone ones? 360 in a 68 fury

I have a question regarding the blower and heater unit in my 68Fury III. The car originally had an AC which is no longer persent and I rarely drive it to the extend that I really need the heater either, except a windshield defrost is 100% necessary. So this isn't a question for the purists...

I got a stronger efan from Spal last year and got tired if my ugly looking cookie sheet shroud. I just got done building a new one out of sheetmetal aluminium and some L profile. Looks way better and should seal way better against the radiator. This should cool it down at an idle way quicker...

Hello, this is notregarding a c-body but more of a general question. Our daily driver has a leak in the ac liquid line (clearly a hole in it and jb weld wont do the trick). I found special compression fittings for a 5/16 AC line repair but am wondering if i should bend a new piece of tubing for...

So, I just got my American eagle 2 row radiator with 1" tubes. The radiator is a bit slimmer than the standard and it looks like the lines for the trans cooling will be 1" or so too short. How would you guys cheaply extend this without having a flare tool?

I am looking to buy a new aluminium radiator this spring. I looked at the champion radiators and they have some options. I'm looking at: 2 row 1" tubes 3 row 4 row I have a 2300cfm electric fan with the standard 22" radiator and a shroud I set it so that it keeps it around 180 degrees...

My fury gets quite hot when its 110° out and I am looking to put in abetter than stock radiator. I have been reading quite a bit on the champion radiators but cant seem to find one which has the right inlet/outlet on the drivers side. I came across something on the bay:FOR 63-69 DODGE...

Are all Petcocks (drain tap) on a 68 plymouth 1/4 inch or what thread do they have? I am trying to figure out how I can install a coolant sensor, I cant get the plugs out of my manifold.... and need the one spot i have for the sensor already in there. So i thought, just remove the petcock and...

Which fan size do I need for my 68 fury with a 360? There are 16" and 19".... my electric fan stopped working and did not bring the improvement i had hoped for anyways so it goes back out.

So im driving my kiddos to school this morning.... everying as usual, temp just fine in the middle, little traffic and I hear my fan kick on.... About 2/3 of the way to the school i noticed the gauge climbing up while sitting at lights. Well, the darn fan crapped out. I dropped them off and...

What would be the correct hose to use for a 360 with no AC in a 68 Fury III? The car originally had ac but thats not abroad anymore... Im having some temps on the gauge i havent seen before and just changed my thermostat and housing and noticed that the radiator hoses dont look too reliable...

Wanted to install my electric fan and thermostat today but I couldnt get one of the blank plugs out of the manifold. Its like they are welded in place, is there an easy trick to get them out other than drilling? Maybe put dry ice on them? Frustrating, should have taken 30mins and now this....